Who actually carries out the work?

A Gas Safe and, where relevant, OFTEC registered engineer from our own small team carries out the job — we don't sub the install out to a third party after quoting. You deal with the same people from survey through to commissioning and any aftercare calls.

Is oil more expensive to run than mains gas?

Oil and gas prices both move with the wholesale market and neither is fixed, so a blanket answer isn't honest. What we can say is that a modern condensing oil boiler, correctly sized and commissioned, will run considerably more efficiently than an old non-condensing model — that efficiency gap usually matters more than the fuel choice itself.

How much longer does a full conversion take compared to a straight boiler swap?

A straight like-for-like swap in the same location is typically a single working day. Converting boiler type (for example back boiler to combi, or oil to LPG), relocating the boiler, or adding a new cylinder usually needs one to two extra days for additional pipework, flue routing, and electrical work, which we'll scope out at survey.

How do we decide between a combi boiler and a boiler-plus-cylinder system?

It comes down to hot water demand and available space. A combi heats water on demand with no cylinder to fill, which suits smaller households and single-bathroom homes, while a system or regular boiler with a cylinder stores hot water and copes far better where two bathrooms or a bath and shower run at the same time.

Is a boiler install a noisy, disruptive job?

There's unavoidable noise — drilling for the flue, pipework, sometimes moving a cylinder — but a straightforward swap is usually done within a working day with the mess kept to the immediate work area. We dust-sheet the route in and out and clear away pipe offcuts and old parts before we leave.

What's actually checked during an annual boiler service?

A service includes a visual and functional check of the boiler's casing and controls, flue gas analysis to confirm safe and efficient combustion, checking the flame picture and pressure, inspecting seals and condensate, and testing safety devices. It's a safety check as much as a performance one, and it's what keeps most manufacturer warranties valid.

Landlord Gas Safety Certificate (CP12)

Landlord Gas Safety Certificate (CP12), Mells

Landlord Gas Safety Certificate (CP12) is something we handle directly from our base at 24 Bristol Road, Radstock BA3 3EE, rather than subcontracting it out. That means one point of contact for the whole job, from the first look at the property through to commissioning and handover. Gas Safe registered, OFTEC registered and a Worcester Bosch Accredited Installer, open Monday to Friday, 8:30am to 5pm on 07516 118198. Terrain is level, which matters for condensate runs and tank siting. homes alongside small commercial and agricultural premises make up most enquiries from this postcode. In Mells itself (BA3, Somerset) that usually means stone cottages and listed buildings, roughly 4 miles from the workshop.

07516 118198 Book a survey

BA3 · Somerset · 4 mi from Radstock · unclassified

Landlord Gas Safety Certificate (CP12) planned around lane access access in Mells, landlord gas safety certificate (cp12) in Mells (BA3) — level setting

Village lanes around here are sometimes narrow enough that arranging a specific arrival time matters more than it would on a wider suburban road, particularly if a new boiler, cylinder or radiators need to be carried some distance from where a van can park. We ask about this when scheduling the survey so the job itself isn't held up by something that could have been sorted in advance. homes alongside small commercial and agricultural premises make up most enquiries from this postcode. Typical era of build is mixed-cottage, which affects existing pipework and system cleanliness. Mells (BA3) has a healthy private-rental sector, particularly across stone cottages and listed buildings. We service a number of letting-agent portfolios across the area and keep the certification cycle running so renewals never slip.

Why Mells work is specified differently

Your legal duties (summary) — Mells

Annual gas safety check by a Gas Safe engineer
Record (CP12) issued within 28 days
Tenant copy within 28 days, new tenants before move-in
Records kept for 2 years
Action any defects identified — we'll quote in writing

Also covering the lanes around Mells

We cover Mells alongside Leigh upon Mendip (BA3), Buckland Dinham (BA11), Kilmersdon (BA3), Stratton-on-the-Fosse (BA3) — so spares, follow-ups and annual visits are easy to schedule together.

Why Mells households use us

Portfolio reminders

Rolling 30-day reminders across every property — no missed renewals.

Gas Safe 549918

Notified, certified, fully insured — your statutory obligations covered properly.

Agent billing supported

Direct billing to the letting agent, single engineer across the portfolio.

Same-day digital CP12

Certificate emailed before we leave the property — copy direct to tenant if preferred.

Common queries, answered honestly

Who actually carries out the work?: A Gas Safe and, where relevant, OFTEC registered engineer from our own small team carries out the job — we don't sub the install out to a third party after quoting. You deal with the same people from survey through to commissioning and any aftercare calls.
Is oil more expensive to run than mains gas?: Oil and gas prices both move with the wholesale market and neither is fixed, so a blanket answer isn't honest. What we can say is that a modern condensing oil boiler, correctly sized and commissioned, will run considerably more efficiently than an old non-condensing model — that efficiency gap usually matters more than the fuel choice itself.
How much longer does a full conversion take compared to a straight boiler swap?: A straight like-for-like swap in the same location is typically a single working day. Converting boiler type (for example back boiler to combi, or oil to LPG), relocating the boiler, or adding a new cylinder usually needs one to two extra days for additional pipework, flue routing, and electrical work, which we'll scope out at survey.
How do we decide between a combi boiler and a boiler-plus-cylinder system?: It comes down to hot water demand and available space. A combi heats water on demand with no cylinder to fill, which suits smaller households and single-bathroom homes, while a system or regular boiler with a cylinder stores hot water and copes far better where two bathrooms or a bath and shower run at the same time.
Is a boiler install a noisy, disruptive job?: There's unavoidable noise — drilling for the flue, pipework, sometimes moving a cylinder — but a straightforward swap is usually done within a working day with the mess kept to the immediate work area. We dust-sheet the route in and out and clear away pipe offcuts and old parts before we leave.
What's actually checked during an annual boiler service?: A service includes a visual and functional check of the boiler's casing and controls, flue gas analysis to confirm safe and efficient combustion, checking the flame picture and pressure, inspecting seals and condensate, and testing safety devices. It's a safety check as much as a performance one, and it's what keeps most manufacturer warranties valid.

Mells coverage and distances

County: Somerset
Postcode district: BA3
Settlement type: village
Nearest classified road: unclassified
Distance from our base: 4 miles (Radstock, BA3)
Typical building stock: stone cottages and listed buildings
Water hardness: very hard limestone water
Fuel availability: mains gas with off-grid pockets
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Leigh upon Mendip, Buckland Dinham, Kilmersdon, Stratton-on-the-Fosse

Technical notes for this job type

Single-pipe circuits in older stone cottages

A lot of the stone cottages and farmhouses around Mells were plumbed decades ago on a single-pipe gravity circuit, where each radiator draws from and returns to the same loop rather than having its own flow and return. It works, but radiators furthest from the boiler receive water that's already cooled after giving up heat to the ones before it, so the far end of the house is always the coldest. Converting to a two-pipe layout means new pipe runs, which in a stone cottage often means chasing lime plaster or lifting flagstones — not a trivial job. Where a full rewire of the pipework isn't wanted, we sometimes improve balance instead by oversizing the radiators nearest the end of the run and fitting TRVs to hold back the ones nearest the boiler.

Chasing pipework into lime plaster and stone walls

Solid stone or cob walls finished in lime plaster, common in the older parts of Mells, behave very differently to modern plasterboard when a pipe run needs chasing in. Lime plaster is softer and more porous than gypsum, so cutting a neat, consistent chase without blowing the surface needs a slower hand and finer disc than a stud-wall job, and any repair has to be made good in a lime-based skim rather than modern filler, which can trap moisture behind it and cause the patch to fail. On solid stone we sometimes surface-mount pipework in painted conduit instead of chasing, particularly where the wall is a significant structural thickness and chasing would weaken it. Knowing which approach a wall needs before starting avoids expensive plaster damage.

Common boiler fault codes and what usually causes them

Most modern boilers display a fault code on the control panel when they lock out, and while the exact code differs between manufacturers, the underlying causes cluster into a small number of categories: low system pressure (often from a small leak or after bleeding radiators), ignition failure (a worn electrode, gas supply issue, or blocked condensate causing a safety shutdown), or a failed sensor reporting an implausible temperature reading. A condensate blockage or freeze specifically tends to show a distinct code from a genuine ignition fault, which is why checking the external condensate pipe for ice before calling out an engineer in a cold snap can sometimes resolve the issue without a visit at all. We ask for the exact fault code and any recent history — a bled radiator, a cold snap, a recent service — before attending, since it often narrows down the likely cause before we arrive.

Village lane access and van positioning for larger jobs

Village lanes around Mells are often single-track or tight two-way roads without dedicated off-street loading space, which affects how a larger job like a full system installation or an oil tank replacement is planned — the van needs somewhere to park close enough for repeated trips carrying equipment without blocking the lane for through traffic or farm vehicles. On a job involving a full radiator or pipework replacement, materials sometimes need staging over more than one visit rather than delivered all at once if there's nowhere secure to leave them on-site between visits. We check lane width and passing places when scheduling larger jobs in village locations, and plan van access and parking as part of the job rather than as an afterthought on the day.

How a condensing boiler recovers extra heat

A condensing boiler passes flue gases through a secondary heat exchanger before they leave the flue, extracting additional heat by condensing water vapour in the exhaust back into liquid, which is expelled as the mildly acidic condensate water down the drain. This is why every condensing boiler needs a condensate drainage route as part of its installation, unlike older non-condensing boilers, which simply vented hot dry gas straight out. The efficiency benefit only fully materialises when the boiler is actually condensing regularly, which needs a return water temperature low enough — generally below 55°C — for water vapour to condense in the first place. A condensing boiler run permanently at a high flow temperature can spend much of its time not actually condensing, which is one of the main reasons flow temperature settings matter as much as the boiler model chosen.

Wood-burning stoves with a back boiler alongside a main boiler

Some older rural properties around Mells run a wood-burning stove with a back boiler feeding heat into the same central heating circuit as an oil or gas boiler, usually through a thermal store or a cylinder with two coils. Getting this combination to work safely means the stove's back boiler circuit has its own means of dissipating heat if the pump fails or a valve closes while the stove is still burning — a stove can't simply be switched off the way a boiler can if its heat has nowhere to go, so a gravity-fed safety circuit or heat leak radiator is normally required. It's a more involved design than a single-boiler system and needs planning at the point either appliance is replaced, not treated as an afterthought once the new boiler is already fitted.

Chimney liners for boilers using an existing flue

Where an older boiler used the property's original brick or stone chimney as its flue route, a replacement condensing boiler usually can't use the same masonry flue unlined, because the flue gases are cooler and wetter and will attack unprotected brickwork and mortar over time. A correctly specified stainless steel liner, sized to the boiler manufacturer's flue length and diameter tables, carries the flue gases safely and lets the existing chimney be reused rather than needing a new wall or roof penetration — often the only realistic option on a listed or solid-wall property in Mells where an external flue run isn't permitted. The liner has to be inspected and swept as part of ongoing servicing exactly as an open-fire flue would be, which is easy to overlook once it's hidden inside the chimney.

Where to go from here

Expect three things from landlord gas safety certificate (cp12) with us: a proper look at the property before any figure is given, a written quote that spells out what's included, and work carried out by a Gas Safe and OFTEC registered engineer who stands behind it. A written quote follows the survey — no pressure, and no charge for the Mells visit. Conservation and listed constraints apply to parts of the area, so external work is checked first. Our van runs the unclassified to reach you, 4 miles out from the Radstock workshop.

07516 118198 All services in Mells

Related help for Mells

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote