Who actually carries out the work?

A Gas Safe and, where relevant, OFTEC registered engineer from our own small team carries out the job — we don't sub the install out to a third party after quoting. You deal with the same people from survey through to commissioning and any aftercare calls.

Is it worth upgrading the heating controls when we replace the boiler?

Where the existing controls are an old mechanical timer and single room thermostat, replacing them alongside the boiler with weather compensation or a modern programmable thermostat usually improves comfort and efficiency more than the boiler swap alone. It's not compulsory, but it's often the single best-value addition to a new install.

Could we switch from oil to mains gas if it's nearby?

It depends entirely on whether a gas main actually runs past the property — some parts of the Somerset patch we cover have gas on one side of the road and none on the other. We can check with the network on request; if it's there, a conversion is a bigger job than a swap but often worthwhile long-term.

Is a magnetic filter really necessary, or is it an upsell?

It's a genuine manufacturer requirement, not an add-on we invent — most boiler warranties are conditional on a system filter being fitted, particularly on hard water. The filter catches magnetite sludge and debris circulating in the system before it reaches the boiler's heat exchanger, which is what actually causes blockages and noise over time.

Is oil more expensive to run than mains gas?

Oil and gas prices both move with the wholesale market and neither is fixed, so a blanket answer isn't honest. What we can say is that a modern condensing oil boiler, correctly sized and commissioned, will run considerably more efficiently than an old non-condensing model — that efficiency gap usually matters more than the fuel choice itself.

Is a Worcester install more expensive in Hemington?

Marginally on the boiler itself, but as Worcester Accredited Installers we can register the full 10-year guarantee*, which usually justifies it on the running-cost side.

New Boiler Cost

New Boiler Cost for Hemington Homes

Some properties make new boiler cost straightforward; others need a bit more thought about parking, access to the boiler cupboard, or how equipment gets in and out. We factor that into the visit rather than discovering it on the day. Working from 24 Bristol Road, Radstock BA3 3EE across the Radstock, Bath and Mendip area, we're Gas Safe registered and OFTEC registered, so both mains gas and oil-fired work is covered under one roof. Nearest neighbours on our round are Faulkland, Kilmersdon, Norton St Philip. homes alongside small commercial and agricultural premises make up most enquiries from this postcode. In Hemington itself (BA3, Somerset) that usually means stone farmhouses and cottages, roughly 3 miles from the workshop.

07516 118198 Book a survey

BA3 · Somerset · 3 mi from Radstock · unclassified

Heating system upgrade in Hemington, very hard limestone water area, new boiler cost in Hemington (BA3) — unclassified corridor

This area has a genuine mix of mains gas and oil-fired properties, sometimes on the same street, depending on when the gas network reached that particular row of houses. It's worth confirming which fuel your property is actually on and whether a fuel switch is realistic before assuming either option is off the table. Being registered for both Gas Safe and OFTEC work means we can look at the honest options for your specific property rather than steering you toward whichever fuel we happen to be set up for. Mains gas covers much of the area, with off-grid pockets, which changes the appliance shortlist. Access is lane access, so parking, spoil removal and delivery timing get planned in advance. What changes a new boiler price in Hemington more than the brand is the building itself: stone farmhouses and cottages drive different flue routes, gas-pipe sizing and controls choices. That's why we visit before fixing a price.

Proof, paperwork and accountability

Fixed written prices

No verbal-only quotes — every figure is in writing with the boiler, controls and warranty spelled out.

No commission selling

Our engineers aren't paid on what you buy — there's no incentive to upsell you to a bigger boiler.

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

Checkatrade 9.9/10

362+ verified reviews from real customers across BA and BS postcodes.

Why Hemington work is specified differently

What changes the price — Hemington

Boiler type (combi vs system vs regular)
Flue route and length
Gas / oil supply pipe sizing
Controls (basic, smart, weather-comp)
Power-flush vs chemical clean
Condensate routing and any external works

Where else we work near Hemington

We cover Hemington alongside Faulkland (BA3), Kilmersdon (BA3), Norton St Philip (BA2), Holcombe (BA3) — so spares, follow-ups and annual visits are easy to schedule together.

Questions before you book

Who actually carries out the work?: A Gas Safe and, where relevant, OFTEC registered engineer from our own small team carries out the job — we don't sub the install out to a third party after quoting. You deal with the same people from survey through to commissioning and any aftercare calls.
Is it worth upgrading the heating controls when we replace the boiler?: Where the existing controls are an old mechanical timer and single room thermostat, replacing them alongside the boiler with weather compensation or a modern programmable thermostat usually improves comfort and efficiency more than the boiler swap alone. It's not compulsory, but it's often the single best-value addition to a new install.
Could we switch from oil to mains gas if it's nearby?: It depends entirely on whether a gas main actually runs past the property — some parts of the Somerset patch we cover have gas on one side of the road and none on the other. We can check with the network on request; if it's there, a conversion is a bigger job than a swap but often worthwhile long-term.
Is a magnetic filter really necessary, or is it an upsell?: It's a genuine manufacturer requirement, not an add-on we invent — most boiler warranties are conditional on a system filter being fitted, particularly on hard water. The filter catches magnetite sludge and debris circulating in the system before it reaches the boiler's heat exchanger, which is what actually causes blockages and noise over time.
Is oil more expensive to run than mains gas?: Oil and gas prices both move with the wholesale market and neither is fixed, so a blanket answer isn't honest. What we can say is that a modern condensing oil boiler, correctly sized and commissioned, will run considerably more efficiently than an old non-condensing model — that efficiency gap usually matters more than the fuel choice itself.
Is a Worcester install more expensive in Hemington?: Marginally on the boiler itself, but as Worcester Accredited Installers we can register the full 10-year guarantee*, which usually justifies it on the running-cost side.

Local reference data

County: Somerset
Postcode district: BA3
Settlement type: village
Nearest classified road: unclassified
Distance from our base: 3 miles (Radstock, BA3)
Typical building stock: stone farmhouses and cottages
Water hardness: very hard limestone water
Fuel availability: mains gas with off-grid pockets
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Faulkland, Kilmersdon, Norton St Philip, Holcombe

The parts of the job people rarely mention

Oil tank de-sludging: why it's not optional

Oil sitting in a tank for years accumulates water from condensation and fine sediment that settles at the bottom, and over time this forms a sludge layer that can be drawn into the fuel line, particularly when the tank is nearly empty and the outlet pulls from lower in the tank than usual. Sludge blocks fine oil filters and burner nozzles, which shows up as burner lockouts or a boiler that won't fire cleanly rather than as an obvious tank problem. De-sludging drains and cleans the tank base without necessarily removing the whole tank, and it's worth doing when a tank is inherited with a property, before switching to a new boiler, or if lockouts recur despite the filter and nozzle being replaced. It's a preventative job that's cheaper done on schedule than after a burner failure it caused.

Chasing pipework into lime plaster and stone walls

Solid stone or cob walls finished in lime plaster, common in the older parts of Hemington, behave very differently to modern plasterboard when a pipe run needs chasing in. Lime plaster is softer and more porous than gypsum, so cutting a neat, consistent chase without blowing the surface needs a slower hand and finer disc than a stud-wall job, and any repair has to be made good in a lime-based skim rather than modern filler, which can trap moisture behind it and cause the patch to fail. On solid stone we sometimes surface-mount pipework in painted conduit instead of chasing, particularly where the wall is a significant structural thickness and chasing would weaken it. Knowing which approach a wall needs before starting avoids expensive plaster damage.

LPG as an alternative to oil off the gas grid

Properties around Hemington that sit off the mains gas network aren't limited to oil — bulk LPG, stored in an above-ground tank on a concrete base with the same OFTEC-style clearance and access rules as oil, runs standard gas-rated boilers with only a change of injector and pressure setting rather than a different boiler entirely. It suits households that want a gas hob and gas-style modulation rather than an oil burner's on/off firing pattern. The tank still needs delivery access for a tanker, which on some rural driveways is the deciding factor over oil. We check the access route for the largest realistic delivery vehicle before recommending LPG over oil, because a tank that can't be filled easily causes more disruption than the fuel choice was meant to solve.

Signs a boiler repair is no longer the right call

A boiler that's failing repeatedly, needing a different part replaced every service, or over roughly ten to fifteen years old is approaching the point where continued repair costs more over time than replacement, particularly once a heat exchanger — the most expensive single part — starts to show signs of failure through leaks or reduced output. Efficiency is the other half of the calculation: an older non-condensing boiler running at 70-80% efficiency against a modern condensing combi at over 90% means a meaningful chunk of every unit of fuel burned in the old boiler is simply lost up the flue. We give a straight answer on repair versus replace based on the fault found and the boiler's age and condition, rather than defaulting to whichever is more profitable to us on the day.

Why very hard limestone water shortens boiler life around Hemington

The limestone geology under Somerset gives Hemington very hard limestone water, which drops calcium carbonate out of solution as soon as it's heated. Inside a combi's plate heat exchanger the gaps between plates are only a millimetre or two wide, so scale narrows the waterways long before it's visible anywhere else in the system. The first symptom is usually a hot tap that runs warm rather than hot, or a boiler that fires more often for the same demand. Left unchecked, scale insulates the exchanger from the burner, forces flue gases hotter, and can crack the exchanger from thermal stress. A scale reducer fitted on the mains feed, sized to the property's flow rate, is cheaper to install once than to replace a heat exchanger twice.

Pumped-oil versus gravity feed: does it matter?

Older oil systems sometimes still rely on gravity feed, where the tank sits higher than the burner and oil flows down to it under its own weight; a pumped system uses the burner's internal pump to draw oil up from a tank at any level, including below the boiler. Gravity feed limits where a tank can be sited and is more prone to airlocks if the line runs dry, while a pumped system is more flexible on tank position but needs the pipe run and lift height kept within the burner pump's rated capacity — usually no more than a few metres of lift and a set maximum run length. When we replace an oil boiler we check which type the existing tank and pipework support before assuming a straight swap, because a tank sited for gravity feed may need repositioning or a different pump to suit a modern burner.

Working across Somerset: what being local changes

Being based at 24 Bristol Road, Radstock, 3 miles from Hemington via the unclassified, means a callout doesn't involve a long cross-county drive, and it also means familiarity with the recurring patterns in the local building stock — stone farmhouses and cottages — rather than encountering that construction type for the first time on-site. Local knowledge doesn't replace a proper site survey, but it does mean fewer surprises: knowing in advance that a particular postcode area typically has hard water, older single-pipe circuits, or restricted parking means the quote reflects the likely reality of the job before the first visit. We're Gas Safe and OFTEC registered and work across Somerset on that basis, not by claiming coverage we don't actually deliver on.

How a condensing boiler recovers extra heat

A condensing boiler passes flue gases through a secondary heat exchanger before they leave the flue, extracting additional heat by condensing water vapour in the exhaust back into liquid, which is expelled as the mildly acidic condensate water down the drain. This is why every condensing boiler needs a condensate drainage route as part of its installation, unlike older non-condensing boilers, which simply vented hot dry gas straight out. The efficiency benefit only fully materialises when the boiler is actually condensing regularly, which needs a return water temperature low enough — generally below 55°C — for water vapour to condense in the first place. A condensing boiler run permanently at a high flow temperature can spend much of its time not actually condensing, which is one of the main reasons flow temperature settings matter as much as the boiler model chosen.

Your next move in BA3

If you're still deciding whether new boiler cost is the right move for your property, a site visit and honest conversation costs you nothing but time. We'll tell you if we think repair is a better option than replacement, or if the job is more or less involved than you expected. We can usually pair the visit with other work in Faulkland to keep the trip efficient. Access is lane access, so parking, spoil removal and delivery timing get planned in advance. Nearest neighbours on our round are Faulkland, Kilmersdon, Norton St Philip.

07516 118198 All services in Hemington

Related help for Hemington

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote