What are your opening hours, and can you help out of hours?

Our published hours are Monday to Friday, 8:30am to 5pm, and that's when the phones are answered and jobs are booked. We're honest that we don't run a round-the-clock emergency line, so if you're planning ahead, call during those hours on 07516 118198 and we'll get you booked in.

What actually happens on install day?

The engineer isolates the gas or oil supply and water, removes the old boiler, fits and pressure-tests the new one, connects the flue and condensate, and commissions the system. For a straight swap this is usually one day; a conversion, relocation, or cylinder change can run into a second depending on the pipework involved.

What is condensate and why does its routing matter?

Condensate is the mildly acidic water produced by a modern condensing boiler as it extracts extra heat from the flue gases, and it needs a route to an internal drain or, less ideally, an external soakaway. In colder or more exposed locations an external condensate pipe can freeze and shut the boiler down, so internal routing is worth prioritising where the layout allows it.

How do we decide between a combi boiler and a boiler-plus-cylinder system?

It comes down to hot water demand and available space. A combi heats water on demand with no cylinder to fill, which suits smaller households and single-bathroom homes, while a system or regular boiler with a cylinder stores hot water and copes far better where two bathrooms or a bath and shower run at the same time.

We run a holiday let — do the same gas safety rules apply as a standard rental?

Yes, holiday lets fall under the same landlord gas safety duty as any other let property — an annual CP12 from a Gas Safe registered engineer is required, and it's worth timing the visit for a gap between bookings rather than trying to fit it around guests, which we're happy to help plan around.

Is a magnetic filter really necessary, or is it an upsell?

It's a genuine manufacturer requirement, not an add-on we invent — most boiler warranties are conditional on a system filter being fitted, particularly on hard water. The filter catches magnetite sludge and debris circulating in the system before it reaches the boiler's heat exchanger, which is what actually causes blockages and noise over time.

Boiler Installers in Temple Cloud

Properties in conservation areas or with listed status add an extra layer to boiler installation, particularly around flue positions and anything visible from the street. We factor planning sensitivity into the survey rather than leaving it to be discovered after the quote. Gas Safe registered, OFTEC registered and a Worcester Bosch Accredited Installer, working from 24 Bristol Road, Radstock BA3 3EE, we'll flag where sign-off or a discreet routing is likely to matter. Mains gas covers much of the area, with off-grid pockets, which changes the appliance shortlist. Terrain is level, which matters for condensate runs and tank siting. In Temple Cloud itself (BS39, Somerset) that usually means stone cottages and 1960s housing, roughly 5 miles from the workshop.

07516 118198 Check availability

BS39 · Somerset · 5 mi from Radstock · A37

Boiler Installation on a village property 5 miles from Radstock, boiler installation in Temple Cloud (BS39) — 5 miles from our Radstock base

Within reach of the A37

Beyond Temple Cloud we're frequently on jobs in Clutton (BS39), Marksbury (BA2), Farmborough (BA2) and Hallatrow (BS39) — so spares, follow-ups and annual services are straightforward.

Proof, paperwork and accountability

Fixed written prices

No verbal-only quotes. You'll get the boiler model, controls and warranty in writing before we book.

Checkatrade 9.9/10

362+ verified reviews from real customers across BA and BS postcodes.

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

What you get, start to finish

Combi, system & regular boilers
Like-for-like swaps in a single day
Worcester, Vaillant, Ideal, Grant & more
Up to 10-year manufacturer warranties
Free written quote, no obligation
Local aftercare from a 5-mile base

What the buildings in Temple Cloud change about the job

Stone cottages and farmhouses around here were mostly built long before central heating existed, so pipework and boiler locations have usually been retrofitted at some point, sometimes more than once. Thick stone walls, uneven floor levels and low ceilings can all affect where a boiler or cylinder can practically go, and older stonework doesn't always take fixings the way modern block or brick does. We work around those constraints on site rather than assuming a straightforward install. Typical era of build is mixed-cottage, which affects existing pipework and system cleanliness. Mains gas covers much of the area, with off-grid pockets, which changes the appliance shortlist. Temple Cloud is roughly 5 miles from our Radstock base via the A37. Typical property stock here: stone cottages and 1960s housing. A meaningful share of properties around Temple Cloud are off the gas grid, so oil boiler installs and tank swaps make up a fair part of what we do locally. When we quote boiler installation here we factor in flue routing, condensate fall and gas-supply pipe sizing before the price is fixed.

Common queries, answered honestly

What are your opening hours, and can you help out of hours?: Our published hours are Monday to Friday, 8:30am to 5pm, and that's when the phones are answered and jobs are booked. We're honest that we don't run a round-the-clock emergency line, so if you're planning ahead, call during those hours on 07516 118198 and we'll get you booked in.
What actually happens on install day?: The engineer isolates the gas or oil supply and water, removes the old boiler, fits and pressure-tests the new one, connects the flue and condensate, and commissions the system. For a straight swap this is usually one day; a conversion, relocation, or cylinder change can run into a second depending on the pipework involved.
What is condensate and why does its routing matter?: Condensate is the mildly acidic water produced by a modern condensing boiler as it extracts extra heat from the flue gases, and it needs a route to an internal drain or, less ideally, an external soakaway. In colder or more exposed locations an external condensate pipe can freeze and shut the boiler down, so internal routing is worth prioritising where the layout allows it.
How do we decide between a combi boiler and a boiler-plus-cylinder system?: It comes down to hot water demand and available space. A combi heats water on demand with no cylinder to fill, which suits smaller households and single-bathroom homes, while a system or regular boiler with a cylinder stores hot water and copes far better where two bathrooms or a bath and shower run at the same time.
We run a holiday let — do the same gas safety rules apply as a standard rental?: Yes, holiday lets fall under the same landlord gas safety duty as any other let property — an annual CP12 from a Gas Safe registered engineer is required, and it's worth timing the visit for a gap between bookings rather than trying to fit it around guests, which we're happy to help plan around.
Is a magnetic filter really necessary, or is it an upsell?: It's a genuine manufacturer requirement, not an add-on we invent — most boiler warranties are conditional on a system filter being fitted, particularly on hard water. The filter catches magnetite sludge and debris circulating in the system before it reaches the boiler's heat exchanger, which is what actually causes blockages and noise over time.

Where to go from here

The next step for boiler installation is a site visit, not a phone-only estimate. Seeing the property, the current system and the access lets us give you a figure that holds up once the work starts, rather than one that changes on the day. Call 07516 118198, Monday to Friday, 8:30am to 5pm, and we'll arrange a time that suits. Gas work is signed off Gas Safe; oil work is signed off OFTEC. Nearest neighbours on our round are Clutton, Marksbury, Farmborough. Terrain is level, which matters for condensate runs and tank siting.

07516 118198 All services in Temple Cloud

Local reference data

County: Somerset
Postcode district: BS39
Settlement type: village
Nearest classified road: A37
Distance from our base: 5 miles (Radstock, BA3)
Typical building stock: stone cottages and 1960s housing
Water hardness: hard water
Fuel availability: mains gas with off-grid pockets
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Clutton, Marksbury, Farmborough, Hallatrow

Detail that matters in Temple Cloud

LPG as an alternative to oil off the gas grid

Properties around Temple Cloud that sit off the mains gas network aren't limited to oil — bulk LPG, stored in an above-ground tank on a concrete base with the same OFTEC-style clearance and access rules as oil, runs standard gas-rated boilers with only a change of injector and pressure setting rather than a different boiler entirely. It suits households that want a gas hob and gas-style modulation rather than an oil burner's on/off firing pattern. The tank still needs delivery access for a tanker, which on some rural driveways is the deciding factor over oil. We check the access route for the largest realistic delivery vehicle before recommending LPG over oil, because a tank that can't be filled easily causes more disruption than the fuel choice was meant to solve.

Temple Cloud's place within the wider Somerset area we cover

Temple Cloud is one of several neighbourhoods we work in around the wider area, and while the postcode district and general water hardness and building stock trends are shared with the surrounding district, the specific street-level access, parking and property type still varies enough locally that we treat each visit on its own facts rather than applying a generic area answer. Nearby areas we also cover include Clutton, Marksbury and Farmborough, which is relevant mainly where a customer wants comparable jobs referenced or where a single visit can sensibly cover more than one nearby property in the same trip. The underlying trade standards — Gas Safe, OFTEC, correct commissioning — don't vary by neighbourhood, only the practical details of the job do.

Wood-burning stoves with a back boiler alongside a main boiler

Some older rural properties around Temple Cloud run a wood-burning stove with a back boiler feeding heat into the same central heating circuit as an oil or gas boiler, usually through a thermal store or a cylinder with two coils. Getting this combination to work safely means the stove's back boiler circuit has its own means of dissipating heat if the pump fails or a valve closes while the stove is still burning — a stove can't simply be switched off the way a boiler can if its heat has nowhere to go, so a gravity-fed safety circuit or heat leak radiator is normally required. It's a more involved design than a single-boiler system and needs planning at the point either appliance is replaced, not treated as an afterthought once the new boiler is already fitted.

The case for turning your flow temperature down

Most combi boilers leave the factory set to a flow temperature around 75-80°C, which is far higher than needed for most homes and well above the point where a condensing boiler achieves its best efficiency. Condensing boilers recover extra heat by condensing water vapour out of the flue gases, and that only happens efficiently when the return water temperature is below roughly 55°C — a target easier to hit with a lower flow setting. Dropping the flow temperature to 60°C or lower, and checking radiators can still heat the coldest rooms adequately at that setting, typically improves gas consumption noticeably over a heating season. The setting itself takes minutes to change on the boiler's control panel or app, but it's only worth doing after checking radiator sizing can cope, which is why we check both together rather than adjusting the boiler alone.

Why hard water shortens boiler life around Temple Cloud

The limestone geology under Somerset gives Temple Cloud hard water, which drops calcium carbonate out of solution as soon as it's heated. Inside a combi's plate heat exchanger the gaps between plates are only a millimetre or two wide, so scale narrows the waterways long before it's visible anywhere else in the system. The first symptom is usually a hot tap that runs warm rather than hot, or a boiler that fires more often for the same demand. Left unchecked, scale insulates the exchanger from the burner, forces flue gases hotter, and can crack the exchanger from thermal stress. A scale reducer fitted on the mains feed, sized to the property's flow rate, is cheaper to install once than to replace a heat exchanger twice.

Heating where a home sits alongside commercial premises

Properties around Temple Cloud that combine living accommodation with an attached shop, workshop or other commercial space often need heating designed as genuinely separate zones with independent controls, since a shop's occupied hours and heating demand rarely match the flat or house above it. Where the two shared a single ageing system, splitting them onto separate zone valves — or, on a larger scale, separate boilers — stops one side subsidising or interfering with the other's heating schedule. Commercial space also sometimes falls under different servicing and safety-record obligations than the residential side, depending on how it's used, so it's worth establishing which parts of the building fall under which regime before assuming a single annual service covers everything.

Chasing pipework into lime plaster and stone walls

Solid stone or cob walls finished in lime plaster, common in the older parts of Temple Cloud, behave very differently to modern plasterboard when a pipe run needs chasing in. Lime plaster is softer and more porous than gypsum, so cutting a neat, consistent chase without blowing the surface needs a slower hand and finer disc than a stud-wall job, and any repair has to be made good in a lime-based skim rather than modern filler, which can trap moisture behind it and cause the patch to fail. On solid stone we sometimes surface-mount pipework in painted conduit instead of chasing, particularly where the wall is a significant structural thickness and chasing would weaken it. Knowing which approach a wall needs before starting avoids expensive plaster damage.

Other boiler services in Temple Cloud

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote