What's actually checked during an annual boiler service?

A service includes a visual and functional check of the boiler's casing and controls, flue gas analysis to confirm safe and efficient combustion, checking the flame picture and pressure, inspecting seals and condensate, and testing safety devices. It's a safety check as much as a performance one, and it's what keeps most manufacturer warranties valid.

Will the new boiler work properly with our existing radiators?

Not always without checking. Modern condensing boilers run most efficiently at lower flow temperatures, and radiators originally sized for an old, hotter-running boiler can end up struggling to heat a room adequately at those lower temperatures. We check radiator sizing against a heat loss calculation and flag any that are undersized for the room before installing.

What actually happens on install day?

The engineer isolates the gas or oil supply and water, removes the old boiler, fits and pressure-tests the new one, connects the flue and condensate, and commissions the system. For a straight swap this is usually one day; a conversion, relocation, or cylinder change can run into a second depending on the pipework involved.

What paperwork do I get once the job's finished?

You'll get a Benchmark commissioning checklist for the boiler, a building notice or Building Control completion certificate for notifiable work, manufacturer warranty registration confirmation, and a Gas Safe (or OFTEC) record of the work. Keep these together — they're what a future buyer's solicitor or a warranty claim will ask for.

What's an unvented cylinder and does it need special installation rules?

An unvented cylinder stores mains-pressure hot water without a cold water tank in the loft, giving strong pressure at every outlet. Building Regulations require it to be fitted and commissioned by someone holding a specific unvented cylinder qualification (which we hold), including fitting the correct safety valves, because an incorrectly installed unvented cylinder is a pressure vessel hazard.

Will you come out to a village like Heytesbury?

Heytesbury is part of our core patch (15 miles from base via the A36). Same-week site visits and quick callbacks are normal.

Heytesbury's Local Landlord Gas Safety Certificates Specialist

Some properties make landlord gas safety certificates straightforward; others need a bit more thought about parking, access to the boiler cupboard, or how equipment gets in and out. We factor that into the visit rather than discovering it on the day. Working from 24 Bristol Road, Radstock BA3 3EE across the Radstock, Bath and Mendip area, we're Gas Safe registered and OFTEC registered, so both mains gas and oil-fired work is covered under one roof. Off-grid oil and LPG are common on these lanes, which changes the appliance shortlist.

07516 118198 Book a service

BA12 · Wiltshire · 15 mi from Radstock · A36

Flue and pipework detail from a landlord gas safety certificates job in Wiltshire — moderately hard water water area

Where else we work near Heytesbury

Beyond Heytesbury we're frequently on jobs in Warminster (BA12), Sutton Veny (BA12), Westbury (Wiltshire) (BA13) and Frome (BA11) — so spares, follow-ups and annual services are straightforward.

What landlord gas safety certificates includes here

Gas Safe registered, CP12 issued same day
Tightness test, combustion analysis and flue checks
Tenant access arranged by text or phone
Several properties aligned to one renewal date
Free written quote, no obligation
Local aftercare from a 15-mile base

Local conditions we plan around in BA12

Properties out this way are commonly off the mains gas network, which means oil is often the realistic option rather than a fallback. That changes the shape of the job: tank location and condition, delivery vehicle access, and how the boiler and tank relate to each other on site all need checking before a quote can be accurate. We're OFTEC registered as well as Gas Safe registered, so oil-fired boiler work, tank considerations and servicing are handled properly rather than as a secondary service alongside gas. Water here is moderately hard water, so scale protection is specified accordingly. Heytesbury is roughly 15 miles from our Radstock base via the A36. Typical property stock here: stone cottages. A meaningful share of properties around Heytesbury are off the gas grid, so oil boiler installs and tank swaps make up a fair part of what we do locally. Repair calls in Heytesbury usually get a same-week visit, with most common faults fixed on the first attempt.

Qualifications behind the work

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

Fixed written prices

No verbal-only quotes. You'll get the boiler model, controls and warranty in writing before we book.

Common queries, answered honestly

What's actually checked during an annual boiler service?: A service includes a visual and functional check of the boiler's casing and controls, flue gas analysis to confirm safe and efficient combustion, checking the flame picture and pressure, inspecting seals and condensate, and testing safety devices. It's a safety check as much as a performance one, and it's what keeps most manufacturer warranties valid.
Will the new boiler work properly with our existing radiators?: Not always without checking. Modern condensing boilers run most efficiently at lower flow temperatures, and radiators originally sized for an old, hotter-running boiler can end up struggling to heat a room adequately at those lower temperatures. We check radiator sizing against a heat loss calculation and flag any that are undersized for the room before installing.
What actually happens on install day?: The engineer isolates the gas or oil supply and water, removes the old boiler, fits and pressure-tests the new one, connects the flue and condensate, and commissions the system. For a straight swap this is usually one day; a conversion, relocation, or cylinder change can run into a second depending on the pipework involved.
What paperwork do I get once the job's finished?: You'll get a Benchmark commissioning checklist for the boiler, a building notice or Building Control completion certificate for notifiable work, manufacturer warranty registration confirmation, and a Gas Safe (or OFTEC) record of the work. Keep these together — they're what a future buyer's solicitor or a warranty claim will ask for.
What's an unvented cylinder and does it need special installation rules?: An unvented cylinder stores mains-pressure hot water without a cold water tank in the loft, giving strong pressure at every outlet. Building Regulations require it to be fitted and commissioned by someone holding a specific unvented cylinder qualification (which we hold), including fitting the correct safety valves, because an incorrectly installed unvented cylinder is a pressure vessel hazard.
Will you come out to a village like Heytesbury?: Heytesbury is part of our core patch (15 miles from base via the A36). Same-week site visits and quick callbacks are normal.

Where to go from here

Once we've seen the property, you'll get a written quote for landlord gas safety certificates that sets out exactly what's included — the equipment, the work, and what happens if anything unexpected turns up once we're on site. That gives you something concrete to compare against any other quotes you're getting. We can usually pair the visit with other work in Warminster to keep the trip efficient. Planning constraints are usually light here, so external work is checked first.

07516 118198 All services in Heytesbury

Local reference data

County: Wiltshire
Postcode district: BA12
Settlement type: village
Nearest classified road: A36
Distance from our base: 15 miles (Radstock, BA3)
Typical building stock: stone cottages
Water hardness: moderately hard water
Fuel availability: off-grid oil and LPG common
Customer mix: rural owner-occupiers and smallholdings
Nearby areas covered: Warminster, Sutton Veny, Westbury (Wiltshire), Frome

Things we check around Heytesbury

Single-pipe circuits in older stone cottages

A lot of the stone cottages and farmhouses around Heytesbury were plumbed decades ago on a single-pipe gravity circuit, where each radiator draws from and returns to the same loop rather than having its own flow and return. It works, but radiators furthest from the boiler receive water that's already cooled after giving up heat to the ones before it, so the far end of the house is always the coldest. Converting to a two-pipe layout means new pipe runs, which in a stone cottage often means chasing lime plaster or lifting flagstones — not a trivial job. Where a full rewire of the pipework isn't wanted, we sometimes improve balance instead by oversizing the radiators nearest the end of the run and fitting TRVs to hold back the ones nearest the boiler.

Pumped-oil versus gravity feed: does it matter?

Older oil systems sometimes still rely on gravity feed, where the tank sits higher than the burner and oil flows down to it under its own weight; a pumped system uses the burner's internal pump to draw oil up from a tank at any level, including below the boiler. Gravity feed limits where a tank can be sited and is more prone to airlocks if the line runs dry, while a pumped system is more flexible on tank position but needs the pipe run and lift height kept within the burner pump's rated capacity — usually no more than a few metres of lift and a set maximum run length. When we replace an oil boiler we check which type the existing tank and pipework support before assuming a straight swap, because a tank sited for gravity feed may need repositioning or a different pump to suit a modern burner.

Nozzle replacement and baffle cleaning on oil burners

An oil burner's nozzle atomises fuel into a fine spray for combustion, and it wears from constant fuel flow at pressure, gradually changing the spray pattern away from the burner manufacturer's specification even before it visibly fails. A worn nozzle burns less cleanly, producing more soot that coats the heat exchanger's baffles, and a sooted heat exchanger loses efficiency in the same way scale does on a gas boiler's plates. Standard practice on an annual oil service is to replace the nozzle as a matter of course, rather than wait for a fault, and to remove and clean the baffles so the heat exchanger surfaces are exposed to combustion heat properly again. Skipping nozzle replacement to save a service visit's minor parts cost is a false economy against the fuel wasted by a poorly atomising burner.

Planning a visit out to Heytesbury

At 15 miles from Radstock via the A36, a job in Heytesbury is planned as a full visit rather than a quick call-back, which is why we ask more detail up front — model numbers, symptoms, access notes — so the first visit is more likely to be the one that resolves the issue rather than the one that diagnoses it. For multi-stage work such as a full boiler and system upgrade, we sequence the survey, any preparatory work and the installation to minimise separate trips where the job allows it. It doesn't affect the standard of work or the paperwork completed on-site, but it's a reasonable practical difference from a job five minutes from the workshop, and we're upfront about it when scheduling.

Chasing pipework into lime plaster and stone walls

Solid stone or cob walls finished in lime plaster, common in the older parts of Heytesbury, behave very differently to modern plasterboard when a pipe run needs chasing in. Lime plaster is softer and more porous than gypsum, so cutting a neat, consistent chase without blowing the surface needs a slower hand and finer disc than a stud-wall job, and any repair has to be made good in a lime-based skim rather than modern filler, which can trap moisture behind it and cause the patch to fail. On solid stone we sometimes surface-mount pipework in painted conduit instead of chasing, particularly where the wall is a significant structural thickness and chasing would weaken it. Knowing which approach a wall needs before starting avoids expensive plaster damage.

What different boiler noises usually mean

A kettling or rumbling sound from a boiler is most often scale or sludge build-up on the heat exchanger causing localised boiling as water is trapped and overheated in restricted channels — the heating equivalent of a kettle furring up. A banging or knocking sound in pipework, sometimes called water hammer, is usually caused by a valve closing too quickly or trapped air rather than the boiler itself. A whining or humming sound tends to point to the circulating pump, either from wear or from air in the system reducing lubrication at the bearing. Diagnosing correctly from the noise alone isn't reliable enough to act on without checking system pressure, inhibitor condition and the pump directly, but the noise itself is a useful first indicator of which of those to check first.

Other boiler services in Heytesbury

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote