What paperwork do I get once the job's finished?

You'll get a Benchmark commissioning checklist for the boiler, a building notice or Building Control completion certificate for notifiable work, manufacturer warranty registration confirmation, and a Gas Safe (or OFTEC) record of the work. Keep these together — they're what a future buyer's solicitor or a warranty claim will ask for.

How do you decide whether to repair or replace a boiler?

We weigh the age of the boiler, whether parts are still made for it, how many faults it's had recently, and its running efficiency against a like-for-like or upgraded replacement. If a straightforward part fixes it and the boiler's otherwise sound, we'll say so rather than push a new install you don't need.

What's actually checked during an annual boiler service?

A service includes a visual and functional check of the boiler's casing and controls, flue gas analysis to confirm safe and efficient combustion, checking the flame picture and pressure, inspecting seals and condensate, and testing safety devices. It's a safety check as much as a performance one, and it's what keeps most manufacturer warranties valid.

What does "commissioning" a boiler actually involve?

Commissioning is setting the boiler up correctly for the property rather than just switching it on: checking gas or oil pressure and flow rates, setting flow temperatures, testing safety devices, balancing the system, and completing the manufacturer's Benchmark checklist. Skipping this properly is one of the most common reasons warranty claims get refused later.

Will the new boiler work properly with our existing radiators?

Not always without checking. Modern condensing boilers run most efficiently at lower flow temperatures, and radiators originally sized for an old, hotter-running boiler can end up struggling to heat a room adequately at those lower temperatures. We check radiator sizing against a heat loss calculation and flag any that are undersized for the room before installing.

Can you handle period properties in Calne?

Yes — georgian and victorian terraces are most of what we work on here. Flue routes, condensate runs and external pipework are planned to keep the building's appearance intact.

Calne's Local Oil Boiler Repairs Specialist

Oil Boiler Repairs covers a range of jobs, from straightforward like-for-like swaps to full system redesigns with new pipework, controls and hot water storage. The right approach depends on boiler location, flue length, pump speed, radiator sizing and how the property loses heat. As a Gas Safe and OFTEC registered firm and a Worcester Bosch Accredited Installer working out of Radstock, we specify each install against the building rather than fitting a standard package regardless of fit. Our van runs the A4 to reach you, 15 miles out from the Radstock workshop.

07516 118198 Book a survey

SN11 · Wiltshire · 15 mi from Radstock · A4

Oil Boiler Repairs in a georgian property in Calne, SN11 — 15 miles from our Radstock base

Local conditions we plan around in SN11

Most properties in this settlement sit on the mains gas network, which keeps the fuel choice straightforward and generally opens up the widest range of boiler options. That doesn't remove every complication — flue routing, existing pipework diameter and how the property currently distributes heat still need checking — but it does mean the conversation usually starts from a simpler baseline than in the off-grid villages further out. We're Gas Safe registered for exactly this kind of work. Our van runs the A4 to reach you, 15 miles out from the Radstock workshop. Calne is roughly 15 miles from our Radstock base via the A4. Typical property stock here: Georgian and Victorian terraces. Mains gas covers most of Calne, so the usual choice is between a modern combi or a system boiler with a cylinder — we'll size it correctly for the home, not just swap like-for-like. Repair calls in Calne usually get a same-week visit, with most common faults fixed on the first attempt.

Why Calne households use us

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Local, family-run

Based at 24 Bristol Rd, Radstock — every job is run by the team that quoted it.

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

Nearby villages and neighbourhoods

Beyond Calne we're frequently on jobs in Bromham (SN15), Sandy Lane (SN15), Rowde (SN10) and Melksham (SN12) — so spares, follow-ups and annual services are straightforward.

What oil boiler repairs includes here

Boiler will not fire or keeps locking out
Sooting, puffing and smoky flue faults
Pump, photocell and control diagnostics
Sludge and water in tank dealt with properly
Free written quote, no obligation
Local aftercare from a 15-mile base

Common queries, answered honestly

What paperwork do I get once the job's finished?: You'll get a Benchmark commissioning checklist for the boiler, a building notice or Building Control completion certificate for notifiable work, manufacturer warranty registration confirmation, and a Gas Safe (or OFTEC) record of the work. Keep these together — they're what a future buyer's solicitor or a warranty claim will ask for.
How do you decide whether to repair or replace a boiler?: We weigh the age of the boiler, whether parts are still made for it, how many faults it's had recently, and its running efficiency against a like-for-like or upgraded replacement. If a straightforward part fixes it and the boiler's otherwise sound, we'll say so rather than push a new install you don't need.
What's actually checked during an annual boiler service?: A service includes a visual and functional check of the boiler's casing and controls, flue gas analysis to confirm safe and efficient combustion, checking the flame picture and pressure, inspecting seals and condensate, and testing safety devices. It's a safety check as much as a performance one, and it's what keeps most manufacturer warranties valid.
What does "commissioning" a boiler actually involve?: Commissioning is setting the boiler up correctly for the property rather than just switching it on: checking gas or oil pressure and flow rates, setting flow temperatures, testing safety devices, balancing the system, and completing the manufacturer's Benchmark checklist. Skipping this properly is one of the most common reasons warranty claims get refused later.
Will the new boiler work properly with our existing radiators?: Not always without checking. Modern condensing boilers run most efficiently at lower flow temperatures, and radiators originally sized for an old, hotter-running boiler can end up struggling to heat a room adequately at those lower temperatures. We check radiator sizing against a heat loss calculation and flag any that are undersized for the room before installing.
Can you handle period properties in Calne?: Yes — georgian and victorian terraces are most of what we work on here. Flue routes, condensate runs and external pipework are planned to keep the building's appearance intact.

How to get this priced

Not every enquiry about oil boiler repairs needs a full replacement — sometimes a repair, a service, or a smaller fix solves the problem. We'll tell you which applies once we've had a proper look, rather than recommending the largest job by default. We can usually pair the visit with other work in Bromham to keep the trip efficient. Planning constraints are usually light here, so external work is checked first.

07516 118198 All services in Calne

Calne at a glance

County: Wiltshire
Postcode district: SN11
Settlement type: town
Nearest classified road: A4
Distance from our base: 15 miles (Radstock, BA3)
Typical building stock: Georgian and Victorian terraces
Water hardness: moderately hard water
Fuel availability: mains gas across most of the area
Customer mix: a mix of owner-occupied and rented homes
Nearby areas covered: Bromham, Sandy Lane, Rowde, Melksham

Detail that matters in Calne

Common boiler fault codes and what usually causes them

Most modern boilers display a fault code on the control panel when they lock out, and while the exact code differs between manufacturers, the underlying causes cluster into a small number of categories: low system pressure (often from a small leak or after bleeding radiators), ignition failure (a worn electrode, gas supply issue, or blocked condensate causing a safety shutdown), or a failed sensor reporting an implausible temperature reading. A condensate blockage or freeze specifically tends to show a distinct code from a genuine ignition fault, which is why checking the external condensate pipe for ice before calling out an engineer in a cold snap can sometimes resolve the issue without a visit at all. We ask for the exact fault code and any recent history — a bled radiator, a cold snap, a recent service — before attending, since it often narrows down the likely cause before we arrive.

Pumped-oil versus gravity feed: does it matter?

Older oil systems sometimes still rely on gravity feed, where the tank sits higher than the burner and oil flows down to it under its own weight; a pumped system uses the burner's internal pump to draw oil up from a tank at any level, including below the boiler. Gravity feed limits where a tank can be sited and is more prone to airlocks if the line runs dry, while a pumped system is more flexible on tank position but needs the pipe run and lift height kept within the burner pump's rated capacity — usually no more than a few metres of lift and a set maximum run length. When we replace an oil boiler we check which type the existing tank and pipework support before assuming a straight swap, because a tank sited for gravity feed may need repositioning or a different pump to suit a modern burner.

Nozzle replacement and baffle cleaning on oil burners

An oil burner's nozzle atomises fuel into a fine spray for combustion, and it wears from constant fuel flow at pressure, gradually changing the spray pattern away from the burner manufacturer's specification even before it visibly fails. A worn nozzle burns less cleanly, producing more soot that coats the heat exchanger's baffles, and a sooted heat exchanger loses efficiency in the same way scale does on a gas boiler's plates. Standard practice on an annual oil service is to replace the nozzle as a matter of course, rather than wait for a fault, and to remove and clean the baffles so the heat exchanger surfaces are exposed to combustion heat properly again. Skipping nozzle replacement to save a service visit's minor parts cost is a false economy against the fuel wasted by a poorly atomising burner.

How a condensing boiler recovers extra heat

A condensing boiler passes flue gases through a secondary heat exchanger before they leave the flue, extracting additional heat by condensing water vapour in the exhaust back into liquid, which is expelled as the mildly acidic condensate water down the drain. This is why every condensing boiler needs a condensate drainage route as part of its installation, unlike older non-condensing boilers, which simply vented hot dry gas straight out. The efficiency benefit only fully materialises when the boiler is actually condensing regularly, which needs a return water temperature low enough — generally below 55°C — for water vapour to condense in the first place. A condensing boiler run permanently at a high flow temperature can spend much of its time not actually condensing, which is one of the main reasons flow temperature settings matter as much as the boiler model chosen.

Radiator sizing after lowering the flow temperature

Running a boiler at a lower flow temperature — typically 55°C or below rather than the old default of 70-80°C — improves condensing efficiency measurably, but it also reduces the heat output of every radiator in the house, because a radiator's output falls roughly with the square of the temperature difference to the room. Radiators sized correctly for a 75°C flow can end up unable to heat the room properly at 55°C unless they're upsized or supplemented. We check each radiator against the lower design flow temperature before recommending it, and where a room falls short we look at whether a larger single panel, a double panel, or an additional radiator on that circuit closes the gap, rather than pushing the flow temperature back up and giving away the efficiency gain.

Chimney liners for boilers using an existing flue

Where an older boiler used the property's original brick or stone chimney as its flue route, a replacement condensing boiler usually can't use the same masonry flue unlined, because the flue gases are cooler and wetter and will attack unprotected brickwork and mortar over time. A correctly specified stainless steel liner, sized to the boiler manufacturer's flue length and diameter tables, carries the flue gases safely and lets the existing chimney be reused rather than needing a new wall or roof penetration — often the only realistic option on a listed or solid-wall property in Calne where an external flue run isn't permitted. The liner has to be inspected and swept as part of ongoing servicing exactly as an open-fire flue would be, which is easy to overlook once it's hidden inside the chimney.

Other boiler services in Calne

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote