We run a holiday let — do the same gas safety rules apply as a standard rental?

Yes, holiday lets fall under the same landlord gas safety duty as any other let property — an annual CP12 from a Gas Safe registered engineer is required, and it's worth timing the visit for a gap between bookings rather than trying to fit it around guests, which we're happy to help plan around.

What is condensate and why does its routing matter?

Condensate is the mildly acidic water produced by a modern condensing boiler as it extracts extra heat from the flue gases, and it needs a route to an internal drain or, less ideally, an external soakaway. In colder or more exposed locations an external condensate pipe can freeze and shut the boiler down, so internal routing is worth prioritising where the layout allows it.

We've still got an old back boiler behind the fireplace — what's involved in removing it?

Removing a back boiler means capping off the gas and water connections behind the fireplace, making good the opening or fitting a new fire/surround if you're keeping one, and rerouting pipework to the new combi or system boiler's position. It's more work than a like-for-like swap but a common upgrade on the older housing stock in this area.

Our water's not as hard here — do we still need a power flush?

Water hardness affects scale, but sludge from years of corrosion and old radiators builds up regardless of hardness. If your system's been running a long time or you've had cold spots on radiators, a power flush before fitting a new boiler protects it just as much here as anywhere with harder water.

What if a part for my existing boiler isn't available anymore?

Manufacturers stop stocking parts for discontinued models after a number of years, and once that happens a repair simply isn't possible even if the fault itself is minor. We'll confirm parts availability with the manufacturer before quoting a repair, and if it's a dead end we'll explain your replacement options honestly.

Do you cover all of Bromham?

Yes — every street in SN15 that falls under Bromham, plus the lanes towards Melksham and Rowde. We're 14 miles away in Radstock, so most jobs are reached in well under half an hour.

Bromham's Local Boiler Installation Specialist

Before quoting for boiler installation, we start with what's actually there: the existing pipework, the flue route, the water pressure and the age of what you've already got. Guesswork on a heating system leads to call-backs and wasted money, so a proper look at the property comes first. We're Gas Safe registered and OFTEC registered, based at 24 Bristol Road, Radstock BA3 3EE, and we size and specify jobs on what we find on site, not on assumptions. homes alongside small commercial and agricultural premises make up most enquiries from this postcode. Off-grid oil and LPG are common on these lanes, which changes the appliance shortlist. In Bromham itself (SN15, Wiltshire) that usually means stone cottages and modern estates, roughly 14 miles from the workshop.

07516 118198 See our hours

SN15 · Wiltshire · 14 mi from Radstock · A342

Controls and cylinder layout typical of Bromham homes (SN15), boiler installation in Bromham (SN15) — 14 miles from our Radstock base

Bromham: stock, water and fuel supply

Stone cottages and farmhouses around here were mostly built long before central heating existed, so pipework and boiler locations have usually been retrofitted at some point, sometimes more than once. Thick stone walls, uneven floor levels and low ceilings can all affect where a boiler or cylinder can practically go, and older stonework doesn't always take fixings the way modern block or brick does. We work around those constraints on site rather than assuming a straightforward install. Planning constraints are usually light here, so external work is checked first. Access is lane access, so parking, spoil removal and delivery timing get planned in advance. Bromham is roughly 14 miles from our Radstock base via the A342. Typical property stock here: stone cottages and modern estates. A meaningful share of properties around Bromham are off the gas grid, so oil boiler installs and tank swaps make up a fair part of what we do locally. When we quote boiler installation here we factor in flue routing, condensate fall and gas-supply pipe sizing before the price is fixed.

Proof, paperwork and accountability

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Local, family-run

Based at 24 Bristol Rd, Radstock — every job is run by the team that quoted it.

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

Where else we work near Bromham

Beyond Bromham we're frequently on jobs in Melksham (SN12), Rowde (SN10), Calne (SN11) and Westbury (Wiltshire) (BA13) — so spares, follow-ups and annual services are straightforward.

How we run boiler installation on site

Combi, system & regular boilers
Like-for-like swaps in a single day
Worcester, Vaillant, Ideal, Grant & more
Up to 10-year manufacturer warranties
Free written quote, no obligation
Local aftercare from a 14-mile base

Common queries, answered honestly

We run a holiday let — do the same gas safety rules apply as a standard rental?: Yes, holiday lets fall under the same landlord gas safety duty as any other let property — an annual CP12 from a Gas Safe registered engineer is required, and it's worth timing the visit for a gap between bookings rather than trying to fit it around guests, which we're happy to help plan around.
What is condensate and why does its routing matter?: Condensate is the mildly acidic water produced by a modern condensing boiler as it extracts extra heat from the flue gases, and it needs a route to an internal drain or, less ideally, an external soakaway. In colder or more exposed locations an external condensate pipe can freeze and shut the boiler down, so internal routing is worth prioritising where the layout allows it.
We've still got an old back boiler behind the fireplace — what's involved in removing it?: Removing a back boiler means capping off the gas and water connections behind the fireplace, making good the opening or fitting a new fire/surround if you're keeping one, and rerouting pipework to the new combi or system boiler's position. It's more work than a like-for-like swap but a common upgrade on the older housing stock in this area.
Our water's not as hard here — do we still need a power flush?: Water hardness affects scale, but sludge from years of corrosion and old radiators builds up regardless of hardness. If your system's been running a long time or you've had cold spots on radiators, a power flush before fitting a new boiler protects it just as much here as anywhere with harder water.
What if a part for my existing boiler isn't available anymore?: Manufacturers stop stocking parts for discontinued models after a number of years, and once that happens a repair simply isn't possible even if the fault itself is minor. We'll confirm parts availability with the manufacturer before quoting a repair, and if it's a dead end we'll explain your replacement options honestly.
Do you cover all of Bromham?: Yes — every street in SN15 that falls under Bromham, plus the lanes towards Melksham and Rowde. We're 14 miles away in Radstock, so most jobs are reached in well under half an hour.

How to get this priced

Once we've seen the property, you'll get a written quote for boiler installation that sets out exactly what's included — the equipment, the work, and what happens if anything unexpected turns up once we're on site. That gives you something concrete to compare against any other quotes you're getting. Gas work is signed off Gas Safe; oil work is signed off OFTEC. Nearest neighbours on our round are Melksham, Rowde, Calne. Our van runs the A342 to reach you, 14 miles out from the Radstock workshop.

07516 118198 All services in Bromham

Area data we work from

County: Wiltshire
Postcode district: SN15
Settlement type: village
Nearest classified road: A342
Distance from our base: 14 miles (Radstock, BA3)
Typical building stock: stone cottages and modern estates
Water hardness: moderately hard water
Fuel availability: off-grid oil and LPG common
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Melksham, Rowde, Calne, Westbury (Wiltshire)

The parts of the job people rarely mention

Single-pipe circuits in older stone cottages

A lot of the stone cottages and farmhouses around Bromham were plumbed decades ago on a single-pipe gravity circuit, where each radiator draws from and returns to the same loop rather than having its own flow and return. It works, but radiators furthest from the boiler receive water that's already cooled after giving up heat to the ones before it, so the far end of the house is always the coldest. Converting to a two-pipe layout means new pipe runs, which in a stone cottage often means chasing lime plaster or lifting flagstones — not a trivial job. Where a full rewire of the pipework isn't wanted, we sometimes improve balance instead by oversizing the radiators nearest the end of the run and fitting TRVs to hold back the ones nearest the boiler.

What a flue gas combustion analysis actually tells us

A combustion analyser measures the flue gases leaving a boiler — oxygen, carbon dioxide, and carbon monoxide content, along with flue temperature — and from those figures calculates the boiler's actual combustion efficiency and confirms it's burning cleanly rather than producing dangerous carbon monoxide. It's a required part of every gas and oil service and commissioning visit, not an optional extra, because visual inspection alone can't detect incomplete combustion. Readings outside the manufacturer's specified range point to a specific fault — a partially blocked burner, incorrect gas or oil pressure, or a fouled heat exchanger — rather than a general sense that something's wrong. We record the readings on every service so any drift between visits is visible, not just the pass/fail result on the day.

Weather compensation: matching flow temperature to outdoor conditions

Weather compensation uses an external sensor to adjust the boiler's flow temperature automatically as outdoor temperature changes, running a lower flow temperature on a mild day and a higher one on a cold one, rather than the fixed flow temperature most boilers are left on permanently. Because condensing boiler efficiency is highest at lower flow and return temperatures, weather compensation keeps the system closer to peak efficiency across the heating season instead of only on the coldest days it was set up for. It needs a compensation curve set to suit the specific building's heat loss characteristics — the same curve on a well-insulated modern semi and a solid-wall Victorian terrace won't give the same comfort result. We set the curve empirically over the first heating season rather than leaving factory defaults in place.

Condensate soakaways where there's no convenient drain

Properties without a nearby internal waste connection or external gully for the boiler's condensate — common on rural plots around Bromham where the nearest drain run is a long way from the boiler's location — sometimes need a dedicated condensate soakaway instead. This is a small pit filled with granular material that the condensate, which is mildly acidic, can disperse into gradually rather than running to a drain at all. Sizing and siting it correctly matters: it needs to be far enough from foundations and sited where the local ground can actually absorb the modest but steady volume a boiler produces, particularly over a long heating season. Where ground conditions make a soakaway unreliable, running a longer insulated pipe to a proper drainage connection is usually the safer long-term choice even though it's more work to install.

Bromham's place within the wider Wiltshire area we cover

Bromham is one of several neighbourhoods we work in around the wider area, and while the postcode district and general water hardness and building stock trends are shared with the surrounding district, the specific street-level access, parking and property type still varies enough locally that we treat each visit on its own facts rather than applying a generic area answer. Nearby areas we also cover include Melksham, Rowde and Calne, which is relevant mainly where a customer wants comparable jobs referenced or where a single visit can sensibly cover more than one nearby property in the same trip. The underlying trade standards — Gas Safe, OFTEC, correct commissioning — don't vary by neighbourhood, only the practical details of the job do.

What different boiler noises usually mean

A kettling or rumbling sound from a boiler is most often scale or sludge build-up on the heat exchanger causing localised boiling as water is trapped and overheated in restricted channels — the heating equivalent of a kettle furring up. A banging or knocking sound in pipework, sometimes called water hammer, is usually caused by a valve closing too quickly or trapped air rather than the boiler itself. A whining or humming sound tends to point to the circulating pump, either from wear or from air in the system reducing lubrication at the bearing. Diagnosing correctly from the noise alone isn't reliable enough to act on without checking system pressure, inhibitor condition and the pump directly, but the noise itself is a useful first indicator of which of those to check first.

Chasing pipework into lime plaster and stone walls

Solid stone or cob walls finished in lime plaster, common in the older parts of Bromham, behave very differently to modern plasterboard when a pipe run needs chasing in. Lime plaster is softer and more porous than gypsum, so cutting a neat, consistent chase without blowing the surface needs a slower hand and finer disc than a stud-wall job, and any repair has to be made good in a lime-based skim rather than modern filler, which can trap moisture behind it and cause the patch to fail. On solid stone we sometimes surface-mount pipework in painted conduit instead of chasing, particularly where the wall is a significant structural thickness and chasing would weaken it. Knowing which approach a wall needs before starting avoids expensive plaster damage.

Building Control notification for boiler work

Installing or replacing a boiler is notifiable work under Building Regulations, and a Gas Safe or OFTEC registered installer working within their scheme's competent-person arrangements notifies the local authority electronically on completion, which avoids the homeowner having to apply for Building Regulations approval separately and pay a council fee for it. This generates a compliance certificate that matters at the point of selling the property — conveyancing solicitors routinely ask for it, and its absence can hold up a sale. Work carried out by someone outside a competent-person scheme has to be notified to Building Control directly and inspected, which is slower and often more expensive. We notify every applicable installation as standard and the certificate follows automatically.

Other boiler services in Bromham

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote