Can your van get down our lane, or do we need to arrange something?

Most village lanes we work on are manageable in our vehicles, but if it's single-track, has a low bridge, or turning is tight, mention it when you book so we bring the right size van and allow extra time. It's rarely a reason to turn a job down, just something we plan around.

How does LPG heating differ from mains gas day to day?

An LPG boiler works the same way as a mains gas one day to day, but the gas is stored in a tank or cylinders on site and topped up by a supplier rather than piped in continuously. That means keeping an eye on tank levels and arranging deliveries, but appliance choice, controls, and servicing requirements are otherwise very similar.

Being 11 miles out, does that add much time to booking a job in?

Distance from our Radstock base doesn't change how the job's priced or scheduled — we build travel into the working day rather than tacking on a surcharge. It can mean a very early or later start slot to fit the return journey around other bookings, which we'll confirm when we schedule.

We've still got an old back boiler behind the fireplace — what's involved in removing it?

Removing a back boiler means capping off the gas and water connections behind the fireplace, making good the opening or fitting a new fire/surround if you're keeping one, and rerouting pipework to the new combi or system boiler's position. It's more work than a like-for-like swap but a common upgrade on the older housing stock in this area.

Yes. Felton is 11 miles from our workshop at 24 Bristol Road, Radstock BA3 3EE, reached via the A38, and it's a regular part of our working area. We're Gas Safe and OFTEC registered, so we cover both mains gas and oil work out here without treating it as a special trip.

What's the warranty on a new boiler installed in Felton?

Up to 10 years on qualifying Worcester Bosch installs registered through us as Accredited Installers. Other manufacturers typically offer 5–7 years.

Local Boiler Installation for Felton

A heating system fitted properly should be low-maintenance for years, which is why the detail in boiler installation matters more than it might seem at the time: correct sizing, clean pipework, and controls set up to suit how the household actually lives. We're Gas Safe registered, OFTEC registered and a Worcester Bosch Accredited Installer, and we fit accordingly from our workshop at 24 Bristol Road, Radstock BA3 3EE. homes alongside small commercial and agricultural premises make up most enquiries from this postcode. Typical era of build is mixed-cottage, which affects existing pipework and system cleanliness. In Felton itself (BS40, North Somerset) that usually means cottages and modern estates, roughly 11 miles from the workshop.

07516 118198 Speak to the engineer

BS40 · North Somerset · 11 mi from Radstock · A38

Controls and cylinder layout typical of Felton homes (BS40), boiler installation in Felton (BS40) — mixed-cottage build

Nearby villages and neighbourhoods

Beyond Felton we're frequently on jobs in Redhill (BS40), Wrington (BS40), Winford (BS40) and Butcombe (BS40) — so spares, follow-ups and annual services are straightforward.

Registrations and how work is signed off

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

Fixed written prices

No verbal-only quotes. You'll get the boiler model, controls and warranty in writing before we book.

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

Felton: stock, water and fuel supply

Stone cottages and farmhouses around here were mostly built long before central heating existed, so pipework and boiler locations have usually been retrofitted at some point, sometimes more than once. Thick stone walls, uneven floor levels and low ceilings can all affect where a boiler or cylinder can practically go, and older stonework doesn't always take fixings the way modern block or brick does. We work around those constraints on site rather than assuming a straightforward install. Terrain is level, which matters for condensate runs and tank siting. Water here is hard water, so scale protection is specified accordingly. Felton is roughly 11 miles from our Radstock base via the A38. Typical property stock here: cottages and modern estates. A meaningful share of properties around Felton are off the gas grid, so oil boiler installs and tank swaps make up a fair part of what we do locally. When we quote boiler installation here we factor in flue routing, condensate fall and gas-supply pipe sizing before the price is fixed.

The work, step by step

Combi, system & regular boilers
Like-for-like swaps in a single day
Worcester, Vaillant, Ideal, Grant & more
Up to 10-year manufacturer warranties
Free written quote, no obligation
Local aftercare from a 11-mile base

Straight answers for Felton homeowners

Can your van get down our lane, or do we need to arrange something?: Most village lanes we work on are manageable in our vehicles, but if it's single-track, has a low bridge, or turning is tight, mention it when you book so we bring the right size van and allow extra time. It's rarely a reason to turn a job down, just something we plan around.
How does LPG heating differ from mains gas day to day?: An LPG boiler works the same way as a mains gas one day to day, but the gas is stored in a tank or cylinders on site and topped up by a supplier rather than piped in continuously. That means keeping an eye on tank levels and arranging deliveries, but appliance choice, controls, and servicing requirements are otherwise very similar.
Being 11 miles out, does that add much time to booking a job in?: Distance from our Radstock base doesn't change how the job's priced or scheduled — we build travel into the working day rather than tacking on a surcharge. It can mean a very early or later start slot to fit the return journey around other bookings, which we'll confirm when we schedule.
We've still got an old back boiler behind the fireplace — what's involved in removing it?: Removing a back boiler means capping off the gas and water connections behind the fireplace, making good the opening or fitting a new fire/surround if you're keeping one, and rerouting pipework to the new combi or system boiler's position. It's more work than a like-for-like swap but a common upgrade on the older housing stock in this area.
Do you cover Felton?: Yes. Felton is 11 miles from our workshop at 24 Bristol Road, Radstock BA3 3EE, reached via the A38, and it's a regular part of our working area. We're Gas Safe and OFTEC registered, so we cover both mains gas and oil work out here without treating it as a special trip.
What's the warranty on a new boiler installed in Felton?: Up to 10 years on qualifying Worcester Bosch installs registered through us as Accredited Installers. Other manufacturers typically offer 5–7 years.

How to get this priced

For landlords, boiler installation usually needs to fit around a tenancy, so let us know at the outset if the property is occupied and what access arrangements work for the tenant. We'll build that into the quote and the schedule rather than assuming an empty property. Photos of the existing setup speed up pricing for village properties like these. Terrain is level, which matters for condensate runs and tank siting. Planning constraints are usually light here, so external work is checked first.

07516 118198 All services in Felton

Area data we work from

County: North Somerset
Postcode district: BS40
Settlement type: village
Nearest classified road: A38
Distance from our base: 11 miles (Radstock, BA3)
Typical building stock: cottages and modern estates
Water hardness: hard water
Fuel availability: mains gas with off-grid pockets
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Redhill, Wrington, Winford, Butcombe

Things we check around Felton

Combi, system or regular: which suits the property?

A combi boiler heats water directly from the mains on demand with no cylinder or tank, which suits smaller households with modest simultaneous hot water demand and properties with no loft or airing cupboard space to spare. A system boiler heats a stored cylinder, giving stronger and more consistent flow to multiple outlets at once — better suited to larger households or properties with more than one bathroom — while a regular (open-vent) boiler additionally needs a cold feed and expansion tank, usually only chosen now where an existing system layout makes it the simpler swap. On stock like cottages and modern estates the right answer depends on bathroom count and existing pipework layout as much as household size, which is why we ask about actual usage patterns rather than defaulting to whatever's currently fitted.

What OpenTherm controls actually change

A standard on/off thermostat tells the boiler to fire at full output until the room reaches temperature, then switches it off completely — a crude control strategy that causes temperature overshoot and more burner cycling than necessary. An OpenTherm-compatible thermostat instead communicates continuously with a compatible boiler, asking for a modulated flow temperature based on how far the room is from target, so the boiler runs at a lower, steadier output for longer rather than firing at full power in short bursts. The efficiency gain depends on the boiler actually supporting OpenTherm modulation, which not every combi does even where the wiring terminals are compatible. We check the boiler's own specification against the thermostat's control protocol before recommending an upgrade, since fitting an OpenTherm stat on a boiler that ignores the modulation signal wastes the thermostat's main feature.

How a condensing boiler recovers extra heat

A condensing boiler passes flue gases through a secondary heat exchanger before they leave the flue, extracting additional heat by condensing water vapour in the exhaust back into liquid, which is expelled as the mildly acidic condensate water down the drain. This is why every condensing boiler needs a condensate drainage route as part of its installation, unlike older non-condensing boilers, which simply vented hot dry gas straight out. The efficiency benefit only fully materialises when the boiler is actually condensing regularly, which needs a return water temperature low enough — generally below 55°C — for water vapour to condense in the first place. A condensing boiler run permanently at a high flow temperature can spend much of its time not actually condensing, which is one of the main reasons flow temperature settings matter as much as the boiler model chosen.

Commissioning checklist and the Benchmark record

Every new boiler installation comes with a Benchmark commissioning checklist that has to be completed and signed at the point of installation — recording gas or oil pressure readings, flue gas analysis results, system flush confirmation and control settings. It's not paperwork for its own sake: manufacturers require a fully completed Benchmark record as a condition of the boiler's guarantee, and an incomplete or missing record is one of the most common reasons a warranty claim gets refused later. We complete and hand over the Benchmark log, along with the Gas Safe or OFTEC notification, on the day of installation rather than promising to send it on, specifically so the paperwork exists from day one if it's ever needed.

Nozzle replacement and baffle cleaning on oil burners

An oil burner's nozzle atomises fuel into a fine spray for combustion, and it wears from constant fuel flow at pressure, gradually changing the spray pattern away from the burner manufacturer's specification even before it visibly fails. A worn nozzle burns less cleanly, producing more soot that coats the heat exchanger's baffles, and a sooted heat exchanger loses efficiency in the same way scale does on a gas boiler's plates. Standard practice on an annual oil service is to replace the nozzle as a matter of course, rather than wait for a fault, and to remove and clean the baffles so the heat exchanger surfaces are exposed to combustion heat properly again. Skipping nozzle replacement to save a service visit's minor parts cost is a false economy against the fuel wasted by a poorly atomising burner.

Boiler interlock: a Part L requirement, not an extra

Building Regulations Part L requires a "boiler interlock" on new and replacement heating systems — wiring arranged so the boiler and pump cannot run unless a room thermostat or a zone valve is actually calling for heat. Without it, a boiler can cycle needlessly even when no zone in the house wants heat, wasting fuel and adding wear. It's a wiring and control logic requirement rather than a specific product, so it can be satisfied by several different control layouts as long as the end result prevents that unwanted firing. We confirm interlock is correctly wired as part of every boiler installation and note it on the commissioning paperwork, because it's one of the checks Building Control or a competent-person scheme inspection will look for specifically.

Other boiler services in Felton

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote