Does my new boiler need to be notified to Building Control?

Yes — boiler installation and replacement is notifiable work under Building Regulations. As Gas Safe/OFTEC registered installers we self-certify the work through our Competent Person Scheme, which means we notify it directly and you get a certificate without needing to involve the council separately.

How often should a boiler actually be serviced?

Once a year is the standard recommendation from every manufacturer, and most warranty terms make it a condition rather than a suggestion — miss a year and a claim can be refused even if the fault is unrelated. Landlords have a separate legal duty to have gas appliances checked annually regardless of warranty terms.

Can you look over a quote I've already had from another company?

Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.

How do we decide between a combi boiler and a boiler-plus-cylinder system?

It comes down to hot water demand and available space. A combi heats water on demand with no cylinder to fill, which suits smaller households and single-bathroom homes, while a system or regular boiler with a cylinder stores hot water and copes far better where two bathrooms or a bath and shower run at the same time.

Our water's not as hard here — do we still need a power flush?

Water hardness affects scale, but sludge from years of corrosion and old radiators builds up regardless of hardness. If your system's been running a long time or you've had cold spots on radiators, a power flush before fitting a new boiler protects it just as much here as anywhere with harder water.

What is condensate and why does its routing matter?

Condensate is the mildly acidic water produced by a modern condensing boiler as it extracts extra heat from the flue gases, and it needs a route to an internal drain or, less ideally, an external soakaway. In colder or more exposed locations an external condensate pipe can freeze and shut the boiler down, so internal routing is worth prioritising where the layout allows it.

Boiler Installation — Shepton Mallet (BA4)

Getting quotes for boiler installation can feel like a gamble when you don't know the trade. You want someone who turns up when they say they will, explains what they're doing, and leaves you with a system you understand. That's the standard we work to from 24 Bristol Road, Radstock BA3 3EE. We're Gas Safe registered, OFTEC registered and a Worcester Bosch Accredited Installer, so the paperwork and the workmanship both hold up to scrutiny. Our van runs the A37 to reach you, 7 miles out from the Radstock workshop. Planning constraints are usually light here, so external work is checked first. In Shepton Mallet itself (BA4, Somerset) that usually means georgian terraces and modern estates, roughly 7 miles from the workshop.

07516 118198 Ask about the guarantee

BA4 · Somerset · 7 mi from Radstock · A37

Controls and cylinder layout typical of Shepton Mallet homes (BA4), boiler installation in Shepton Mallet (BA4) — level setting

Scope of work, itemised

Combi, system & regular boilers
Like-for-like swaps in a single day
Worcester, Vaillant, Ideal, Grant & more
Up to 10-year manufacturer warranties
Free written quote, no obligation
Local aftercare from a 7-mile base

What backs up a Shepton Mallet quote

Local, family-run

Based at 24 Bristol Rd, Radstock — every job is run by the team that quoted it.

Checkatrade 9.9/10

362+ verified reviews from real customers across BA and BS postcodes.

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

Where else we work near Shepton Mallet

Beyond Shepton Mallet we're frequently on jobs in Croscombe (BA5), Pilton (BA4), Doulting (BA4) and Evercreech (BA4) — so spares, follow-ups and annual services are straightforward.

Why Shepton Mallet work is specified differently

Most properties in this settlement sit on the mains gas network, which keeps the fuel choice straightforward and generally opens up the widest range of boiler options. That doesn't remove every complication — flue routing, existing pipework diameter and how the property currently distributes heat still need checking — but it does mean the conversation usually starts from a simpler baseline than in the off-grid villages further out. We're Gas Safe registered for exactly this kind of work. Terrain is level, which matters for condensate runs and tank siting. Nearest neighbours on our round are Croscombe, Pilton, Doulting. Shepton Mallet is roughly 7 miles from our Radstock base via the A37. Typical property stock here: Georgian terraces and modern estates. Mains gas covers most of Shepton Mallet, so the usual choice is between a modern combi or a system boiler with a cylinder — we'll size it correctly for the home, not just swap like-for-like. When we quote boiler installation here we factor in flue routing, condensate fall and gas-supply pipe sizing before the price is fixed.

Common queries, answered honestly

Does my new boiler need to be notified to Building Control?: Yes — boiler installation and replacement is notifiable work under Building Regulations. As Gas Safe/OFTEC registered installers we self-certify the work through our Competent Person Scheme, which means we notify it directly and you get a certificate without needing to involve the council separately.
How often should a boiler actually be serviced?: Once a year is the standard recommendation from every manufacturer, and most warranty terms make it a condition rather than a suggestion — miss a year and a claim can be refused even if the fault is unrelated. Landlords have a separate legal duty to have gas appliances checked annually regardless of warranty terms.
Can you look over a quote I've already had from another company?: Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.
How do we decide between a combi boiler and a boiler-plus-cylinder system?: It comes down to hot water demand and available space. A combi heats water on demand with no cylinder to fill, which suits smaller households and single-bathroom homes, while a system or regular boiler with a cylinder stores hot water and copes far better where two bathrooms or a bath and shower run at the same time.
Our water's not as hard here — do we still need a power flush?: Water hardness affects scale, but sludge from years of corrosion and old radiators builds up regardless of hardness. If your system's been running a long time or you've had cold spots on radiators, a power flush before fitting a new boiler protects it just as much here as anywhere with harder water.
What is condensate and why does its routing matter?: Condensate is the mildly acidic water produced by a modern condensing boiler as it extracts extra heat from the flue gases, and it needs a route to an internal drain or, less ideally, an external soakaway. In colder or more exposed locations an external condensate pipe can freeze and shut the boiler down, so internal routing is worth prioritising where the layout allows it.

Where to go from here

If boiler installation is something you're looking into, the simplest next step is a call on 07516 118198 during our normal hours, Monday to Friday, 8:30am to 5pm. Tell us a bit about the property and what's prompted the enquiry, and we'll take it from there. Call 07516 118198 and we will confirm a visit slot for BA4. Nearest neighbours on our round are Croscombe, Pilton, Doulting. Terrain is level, which matters for condensate runs and tank siting.

07516 118198 All services in Shepton Mallet

Shepton Mallet at a glance

County: Somerset
Postcode district: BA4
Settlement type: town
Nearest classified road: A37
Distance from our base: 7 miles (Radstock, BA3)
Typical building stock: Georgian terraces and modern estates
Water hardness: moderately hard water
Fuel availability: mains gas across most of the area
Customer mix: a mix of owner-occupied and rented homes
Nearby areas covered: Croscombe, Pilton, Doulting, Evercreech

Things we check around Shepton Mallet

Chasing pipework into lime plaster and stone walls

Solid stone or cob walls finished in lime plaster, common in the older parts of Shepton Mallet, behave very differently to modern plasterboard when a pipe run needs chasing in. Lime plaster is softer and more porous than gypsum, so cutting a neat, consistent chase without blowing the surface needs a slower hand and finer disc than a stud-wall job, and any repair has to be made good in a lime-based skim rather than modern filler, which can trap moisture behind it and cause the patch to fail. On solid stone we sometimes surface-mount pipework in painted conduit instead of chasing, particularly where the wall is a significant structural thickness and chasing would weaken it. Knowing which approach a wall needs before starting avoids expensive plaster damage.

Mixed owner-occupied and rented housing in Shepton Mallet

Shepton Mallet's mix of owner-occupied and rented housing means we regularly work to two different sets of expectations on the same street — a landlord wanting the minimum reliable, compliant system at reasonable cost for a tenanted property, and an owner-occupier next door wanting a longer-term investment in efficiency and comfort. Both are legitimate priorities, but they lead to different specifications: a landlord's replacement boiler decision is often driven by the annual gas safety record and reliable compliance, while an owner-occupier's decision more often factors in flow temperature optimisation and controls for their own daily comfort. We ask which category a job falls into early, since it changes the questions worth asking about the property and the recommendation that follows.

Signs a boiler repair is no longer the right call

A boiler that's failing repeatedly, needing a different part replaced every service, or over roughly ten to fifteen years old is approaching the point where continued repair costs more over time than replacement, particularly once a heat exchanger — the most expensive single part — starts to show signs of failure through leaks or reduced output. Efficiency is the other half of the calculation: an older non-condensing boiler running at 70-80% efficiency against a modern condensing combi at over 90% means a meaningful chunk of every unit of fuel burned in the old boiler is simply lost up the flue. We give a straight answer on repair versus replace based on the fault found and the boiler's age and condition, rather than defaulting to whichever is more profitable to us on the day.

Chimney liners for boilers using an existing flue

Where an older boiler used the property's original brick or stone chimney as its flue route, a replacement condensing boiler usually can't use the same masonry flue unlined, because the flue gases are cooler and wetter and will attack unprotected brickwork and mortar over time. A correctly specified stainless steel liner, sized to the boiler manufacturer's flue length and diameter tables, carries the flue gases safely and lets the existing chimney be reused rather than needing a new wall or roof penetration — often the only realistic option on a listed or solid-wall property in Shepton Mallet where an external flue run isn't permitted. The liner has to be inspected and swept as part of ongoing servicing exactly as an open-fire flue would be, which is easy to overlook once it's hidden inside the chimney.

Weather compensation: matching flow temperature to outdoor conditions

Weather compensation uses an external sensor to adjust the boiler's flow temperature automatically as outdoor temperature changes, running a lower flow temperature on a mild day and a higher one on a cold one, rather than the fixed flow temperature most boilers are left on permanently. Because condensing boiler efficiency is highest at lower flow and return temperatures, weather compensation keeps the system closer to peak efficiency across the heating season instead of only on the coldest days it was set up for. It needs a compensation curve set to suit the specific building's heat loss characteristics — the same curve on a well-insulated modern semi and a solid-wall Victorian terrace won't give the same comfort result. We set the curve empirically over the first heating season rather than leaving factory defaults in place.

Access and parking constraints before we start work

Shepton Mallet's narrow terraced frontages affect how a job is planned before any pipework is touched. A boiler, cylinder or radiators have to be carried in, and on some streets that means checking parking permit zones or loading restrictions in advance rather than on the day; on farm tracks it means confirming a van can actually reach the building in wet weather, since a track that's fine in summer can be impassable after heavy rain. Old equipment being removed — an oil tank, an old cylinder, a cast iron boiler — needs the same access route in reverse, and weight matters as much as width. We ask about access and parking at the quoting stage specifically so it doesn't become a delay on the installation day.

Why a boiler needs a permanently live electrical supply

A boiler's electrical supply has to be permanently live, taken from a fused spur rather than switched off a light circuit or any switch a homeowner might turn off without realising it isolates the boiler along with it. This matters for frost protection especially — a boiler's internal frost thermostat can only bring the system on to prevent freezing if it has power at the time, so a supply that's accidentally switched off overnight defeats frost protection entirely, even though everything else about the installation is correct. We check the existing electrical supply on every boiler swap and, where it's taken from an inappropriate circuit, correct it as part of the installation rather than leaving a known risk in place because it wasn't part of the original job description.

Other boiler services in Shepton Mallet

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote