What's the difference between a boiler service and general maintenance?

A service is the annual manufacturer-required safety and efficiency check that keeps the warranty valid. Maintenance covers everything else — bleeding radiators, checking system pressure, sorting minor faults, and periodic flushing or filter checks — that keeps the system running well between those annual services rather than replacing them.

Is oil more expensive to run than mains gas?

Oil and gas prices both move with the wholesale market and neither is fixed, so a blanket answer isn't honest. What we can say is that a modern condensing oil boiler, correctly sized and commissioned, will run considerably more efficiently than an old non-condensing model — that efficiency gap usually matters more than the fuel choice itself.

What's a CP12 and do I need one as a landlord?

A CP12 (Landlord Gas Safety Record) confirms every gas appliance in a rented property has passed an annual safety check by a Gas Safe registered engineer. It's a legal requirement before letting and at each renewal, a copy has to go to tenants, and it needs to be renewed every 12 months without a gap.

How do you decide whether to repair or replace a boiler?

We weigh the age of the boiler, whether parts are still made for it, how many faults it's had recently, and its running efficiency against a like-for-like or upgraded replacement. If a straightforward part fixes it and the boiler's otherwise sound, we'll say so rather than push a new install you don't need.

How does LPG heating differ from mains gas day to day?

An LPG boiler works the same way as a mains gas one day to day, but the gas is stored in a tank or cylinders on site and topped up by a supplier rather than piped in continuously. That means keeping an eye on tank levels and arranging deliveries, but appliance choice, controls, and servicing requirements are otherwise very similar.

What's the warranty on a new boiler installed in Mells?

Up to 10 years on qualifying Worcester Bosch installs registered through us as Accredited Installers. Other manufacturers typically offer 5–7 years.

Local Maintenance & Repair for Mells

Before quoting for maintenance & repair, we start with what's actually there: the existing pipework, the flue route, the water pressure and the age of what you've already got. Guesswork on a heating system leads to call-backs and wasted money, so a proper look at the property comes first. We're Gas Safe registered and OFTEC registered, based at 24 Bristol Road, Radstock BA3 3EE, and we size and specify jobs on what we find on site, not on assumptions. Terrain is level, which matters for condensate runs and tank siting. Mains gas covers much of the area, with off-grid pockets, which changes the appliance shortlist. In Mells itself (BA3, Somerset) that usually means stone cottages and listed buildings, roughly 4 miles from the workshop.

07516 118198 Compare with confidence

BA3 · Somerset · 4 mi from Radstock · unclassified

Flue and pipework detail from a maintenance & repair job in Somerset, maintenance & repair in Mells (BA3) — Somerset

Nearby villages and neighbourhoods

Beyond Mells we're frequently on jobs in Leigh upon Mendip (BA3), Buckland Dinham (BA11), Kilmersdon (BA3) and Stratton-on-the-Fosse (BA3) — so spares, follow-ups and annual services are straightforward.

Why Mells households use us

Local, family-run

Based at 24 Bristol Rd, Radstock — every job is run by the team that quoted it.

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Fixed written prices

No verbal-only quotes. You'll get the boiler model, controls and warranty in writing before we book.

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

Mells: stock, water and fuel supply

Conservation area status, and in Bath's case UNESCO World Heritage designation, adds a layer of consideration to anything visible from the street, particularly flue positions and external pipework. It doesn't rule out a straightforward boiler replacement, but it does mean the survey needs to look properly at routing options that keep the installation discreet and compliant. We flag this at quote stage rather than after the work has started, so there are no surprises about what can and can't be fitted where. Mains gas covers much of the area, with off-grid pockets, which changes the appliance shortlist. Terrain is level, which matters for condensate runs and tank siting. Mells is roughly 4 miles from our Radstock base via the unclassified. Typical property stock here: stone cottages and listed buildings. Mells sits in the Somerset BA3 postcode and is part of our weekly run, so local response is quick. Repair calls in Mells usually get a same-week visit, with most common faults fixed on the first attempt.

What you get, start to finish

Fast diagnostics
Common faults fixed same-visit
Pumps, valves & PCB replacements
Honest, fixed-price repairs
Free written quote, no obligation
Local aftercare from a 4-mile base

Maintenance & Repair FAQs for BA3

What's the difference between a boiler service and general maintenance?: A service is the annual manufacturer-required safety and efficiency check that keeps the warranty valid. Maintenance covers everything else — bleeding radiators, checking system pressure, sorting minor faults, and periodic flushing or filter checks — that keeps the system running well between those annual services rather than replacing them.
Is oil more expensive to run than mains gas?: Oil and gas prices both move with the wholesale market and neither is fixed, so a blanket answer isn't honest. What we can say is that a modern condensing oil boiler, correctly sized and commissioned, will run considerably more efficiently than an old non-condensing model — that efficiency gap usually matters more than the fuel choice itself.
What's a CP12 and do I need one as a landlord?: A CP12 (Landlord Gas Safety Record) confirms every gas appliance in a rented property has passed an annual safety check by a Gas Safe registered engineer. It's a legal requirement before letting and at each renewal, a copy has to go to tenants, and it needs to be renewed every 12 months without a gap.
How do you decide whether to repair or replace a boiler?: We weigh the age of the boiler, whether parts are still made for it, how many faults it's had recently, and its running efficiency against a like-for-like or upgraded replacement. If a straightforward part fixes it and the boiler's otherwise sound, we'll say so rather than push a new install you don't need.
How does LPG heating differ from mains gas day to day?: An LPG boiler works the same way as a mains gas one day to day, but the gas is stored in a tank or cylinders on site and topped up by a supplier rather than piped in continuously. That means keeping an eye on tank levels and arranging deliveries, but appliance choice, controls, and servicing requirements are otherwise very similar.
What's the warranty on a new boiler installed in Mells?: Up to 10 years on qualifying Worcester Bosch installs registered through us as Accredited Installers. Other manufacturers typically offer 5–7 years.

Next step for Mells

A survey and written quote for maintenance & repair doesn't commit you to anything — it gives you accurate information to make a decision with, whether that's going ahead with us, getting a further comparison, or deciding the timing isn't right yet. Gas work is signed off Gas Safe; oil work is signed off OFTEC. Mains gas covers much of the area, with off-grid pockets, which changes the appliance shortlist. Nearest neighbours on our round are Leigh upon Mendip, Buckland Dinham, Kilmersdon.

07516 118198 All services in Mells

Local reference data

County: Somerset
Postcode district: BA3
Settlement type: village
Nearest classified road: unclassified
Distance from our base: 4 miles (Radstock, BA3)
Typical building stock: stone cottages and listed buildings
Water hardness: very hard limestone water
Fuel availability: mains gas with off-grid pockets
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Leigh upon Mendip, Buckland Dinham, Kilmersdon, Stratton-on-the-Fosse

The parts of the job people rarely mention

Low-loss headers on larger or multi-zone systems

On a system with several heating zones or a boiler oversized relative to any single zone's flow requirement, a low-loss header hydraulically separates the boiler's primary circuit from the secondary zone circuits, so each side can run its own pump and flow rate without one interfering with the other. Without it, a zone valve closing on a multi-zone system can starve the boiler of flow or force excessive pump pressure through the remaining open zones. It's most relevant on larger properties or ones with commercial premises attached, where several distinct heating circuits — perhaps a shop unit and a flat above — share one heat source. Getting the header sized to the boiler's actual flow rate, not just fitted as standard, is what makes it work rather than just adding another connection.

Reaching properties off the main road network

Mells is reached via the unclassified, an unclassified road rather than a numbered route, which matters mainly for winter access and for confirming a delivery vehicle carrying a new oil tank or bulky equipment can realistically reach the property. We factor the actual route in when scheduling deliveries or larger installations, checking with the customer about any width, height or surface restrictions on the final approach rather than assuming a mapping app's route reflects what a loaded van can manage. It rarely changes the technical scope of a job, but it does affect how a visit is planned and timed, particularly for jobs needing a specific delivery slot to coincide with the installation date.

Single-pipe circuits in older stone cottages

A lot of the stone cottages and farmhouses around Mells were plumbed decades ago on a single-pipe gravity circuit, where each radiator draws from and returns to the same loop rather than having its own flow and return. It works, but radiators furthest from the boiler receive water that's already cooled after giving up heat to the ones before it, so the far end of the house is always the coldest. Converting to a two-pipe layout means new pipe runs, which in a stone cottage often means chasing lime plaster or lifting flagstones — not a trivial job. Where a full rewire of the pipework isn't wanted, we sometimes improve balance instead by oversizing the radiators nearest the end of the run and fitting TRVs to hold back the ones nearest the boiler.

Oil tank de-sludging: why it's not optional

Oil sitting in a tank for years accumulates water from condensation and fine sediment that settles at the bottom, and over time this forms a sludge layer that can be drawn into the fuel line, particularly when the tank is nearly empty and the outlet pulls from lower in the tank than usual. Sludge blocks fine oil filters and burner nozzles, which shows up as burner lockouts or a boiler that won't fire cleanly rather than as an obvious tank problem. De-sludging drains and cleans the tank base without necessarily removing the whole tank, and it's worth doing when a tank is inherited with a property, before switching to a new boiler, or if lockouts recur despite the filter and nozzle being replaced. It's a preventative job that's cheaper done on schedule than after a burner failure it caused.

How a condensing boiler recovers extra heat

A condensing boiler passes flue gases through a secondary heat exchanger before they leave the flue, extracting additional heat by condensing water vapour in the exhaust back into liquid, which is expelled as the mildly acidic condensate water down the drain. This is why every condensing boiler needs a condensate drainage route as part of its installation, unlike older non-condensing boilers, which simply vented hot dry gas straight out. The efficiency benefit only fully materialises when the boiler is actually condensing regularly, which needs a return water temperature low enough — generally below 55°C — for water vapour to condense in the first place. A condensing boiler run permanently at a high flow temperature can spend much of its time not actually condensing, which is one of the main reasons flow temperature settings matter as much as the boiler model chosen.

Nozzle replacement and baffle cleaning on oil burners

An oil burner's nozzle atomises fuel into a fine spray for combustion, and it wears from constant fuel flow at pressure, gradually changing the spray pattern away from the burner manufacturer's specification even before it visibly fails. A worn nozzle burns less cleanly, producing more soot that coats the heat exchanger's baffles, and a sooted heat exchanger loses efficiency in the same way scale does on a gas boiler's plates. Standard practice on an annual oil service is to replace the nozzle as a matter of course, rather than wait for a fault, and to remove and clean the baffles so the heat exchanger surfaces are exposed to combustion heat properly again. Skipping nozzle replacement to save a service visit's minor parts cost is a false economy against the fuel wasted by a poorly atomising burner.

Other boiler services in Mells

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote