Lansdown's Local Boiler Servicing Specialist

Condensate pipe freezing on exposed elevations

Properties on the higher ground around Lansdown catch more wind chill than the valley floor, and an external condensate pipe on a north or east-facing wall is the most common cause of a boiler lockout in a cold snap. The pipe carries mildly acidic waste water from the flue; if it's routed externally in 21.5mm pipe rather than run internally and lagged, or dropped into an internal soil stack, it freezes solid and the boiler senses a blockage and shuts down for safety. Building Regulations guidance favours an internal run with a trapped connection to the waste system wherever the layout allows it. Where an external run is unavoidable we use 32mm insulated pipe with a minimal fall, which resists freezing far better than the standard diameter.

Oil tank de-sludging: why it's not optional

Oil sitting in a tank for years accumulates water from condensation and fine sediment that settles at the bottom, and over time this forms a sludge layer that can be drawn into the fuel line, particularly when the tank is nearly empty and the outlet pulls from lower in the tank than usual. Sludge blocks fine oil filters and burner nozzles, which shows up as burner lockouts or a boiler that won't fire cleanly rather than as an obvious tank problem. De-sludging drains and cleans the tank base without necessarily removing the whole tank, and it's worth doing when a tank is inherited with a property, before switching to a new boiler, or if lockouts recur despite the filter and nozzle being replaced. It's a preventative job that's cheaper done on schedule than after a burner failure it caused.

Signs a boiler repair is no longer the right call

A boiler that's failing repeatedly, needing a different part replaced every service, or over roughly ten to fifteen years old is approaching the point where continued repair costs more over time than replacement, particularly once a heat exchanger — the most expensive single part — starts to show signs of failure through leaks or reduced output. Efficiency is the other half of the calculation: an older non-condensing boiler running at 70-80% efficiency against a modern condensing combi at over 90% means a meaningful chunk of every unit of fuel burned in the old boiler is simply lost up the flue. We give a straight answer on repair versus replace based on the fault found and the boiler's age and condition, rather than defaulting to whichever is more profitable to us on the day.

Working across Somerset: what being local changes

Being based at 24 Bristol Road, Radstock, 9 miles from Lansdown via the A431, means a callout doesn't involve a long cross-county drive, and it also means familiarity with the recurring patterns in the local building stock — large detached victorian and edwardian villas — rather than encountering that construction type for the first time on-site. Local knowledge doesn't replace a proper site survey, but it does mean fewer surprises: knowing in advance that a particular postcode area typically has hard water, older single-pipe circuits, or restricted parking means the quote reflects the likely reality of the job before the first visit. We're Gas Safe and OFTEC registered and work across Somerset on that basis, not by claiming coverage we don't actually deliver on.

Do you need listed building consent for a new flue?

Whether a new boiler flue on a listed building in or around Lansdown needs formal listed building consent depends on whether the work affects the building's special architectural or historic character — cutting through an original stone wall or a decorative elevation is far more likely to need consent than routing through a later, non-original extension. Consent has to be granted before the work starts; carrying it out first and applying afterwards is a criminal offence under the Planning (Listed Buildings and Conservation Areas) Act, not just a paperwork formality to tidy up later. We recommend checking with the local planning authority's conservation team at the quoting stage on any listed property, because the answer varies by building and by exactly which wall is proposed, and getting it wrong can mean expensive remedial work to satisfy the authority afterwards.

What a proper heating quote should include

A quote worth relying on states the specific boiler or equipment model, the labour and materials it covers, whether a system flush and magnetic filter are included, what happens to old equipment removal and disposal, and what's excluded — an unexpected gas pipe upsizing or asbestos-containing material discovered during removal, for example, which can't always be known before work starts. It should also state who's completing the Gas Safe or OFTEC notification and Benchmark commissioning record, since that's the paperwork that protects both the manufacturer's guarantee and the property's compliance history when it's sold. A vague one-line quote makes comparing genuinely different offers difficult, because two prices that look similar can cover very different scopes of actual work.

• Specific make and model, not just "combi boiler"
• Flush and magnetic filter stated as included or excluded
• Old equipment removal and disposal covered
• Notification and Benchmark record responsibility stated