How do we decide between a combi boiler and a boiler-plus-cylinder system?

It comes down to hot water demand and available space. A combi heats water on demand with no cylinder to fill, which suits smaller households and single-bathroom homes, while a system or regular boiler with a cylinder stores hot water and copes far better where two bathrooms or a bath and shower run at the same time.

Can you look over a quote I've already had from another company?

Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.

Is oil more expensive to run than mains gas?

Oil and gas prices both move with the wholesale market and neither is fixed, so a blanket answer isn't honest. What we can say is that a modern condensing oil boiler, correctly sized and commissioned, will run considerably more efficiently than an old non-condensing model — that efficiency gap usually matters more than the fuel choice itself.

How do you decide whether to repair or replace a boiler?

We weigh the age of the boiler, whether parts are still made for it, how many faults it's had recently, and its running efficiency against a like-for-like or upgraded replacement. If a straightforward part fixes it and the boiler's otherwise sound, we'll say so rather than push a new install you don't need.

Since Faulkland is so close to your base, can you offer more flexible slot timing?

Being close by does help us fit shorter jobs — like a service or a minor repair — into gaps between other bookings more easily than a longer round trip would allow. For a full installation the timescale is the same either way, since the work itself takes the same amount of time regardless of the drive.

Do you cover all of Faulkland?

Yes — every street in BA3 that falls under Faulkland, plus the lanes towards Hemington and Norton St Philip. We're 3 miles away in Radstock, so most jobs are reached in well under half an hour.

Local Gas Boiler Installation for Faulkland

Some properties make gas boiler installation straightforward; others need a bit more thought about parking, access to the boiler cupboard, or how equipment gets in and out. We factor that into the visit rather than discovering it on the day. Working from 24 Bristol Road, Radstock BA3 3EE across the Radstock, Bath and Mendip area, we're Gas Safe registered and OFTEC registered, so both mains gas and oil-fired work is covered under one roof. Typical era of build is mixed-cottage, which affects existing pipework and system cleanliness. Planning constraints are usually light here, so external work is checked first. In Faulkland itself (BA3, Somerset) that usually means stone cottages and farms, roughly 3 miles from the workshop.

07516 118198 Plan your install

BA3 · Somerset · 3 mi from Radstock · A366

Gas Boiler Installation on a village property 3 miles from Radstock, gas boiler installation in Faulkland (BA3) — mixed-cottage build

How Somerset building stock shapes the spec

Village lanes around here are sometimes narrow enough that arranging a specific arrival time matters more than it would on a wider suburban road, particularly if a new boiler, cylinder or radiators need to be carried some distance from where a van can park. We ask about this when scheduling the survey so the job itself isn't held up by something that could have been sorted in advance. Our van runs the A366 to reach you, 3 miles out from the Radstock workshop. Typical era of build is mixed-cottage, which affects existing pipework and system cleanliness. Faulkland is roughly 3 miles from our Radstock base via the A366. Typical property stock here: stone cottages and farms. Faulkland sits in the Somerset BA3 postcode and is part of our weekly run, so local response is quick. When we quote gas boiler installation here we factor in flue routing, condensate fall and gas-supply pipe sizing before the price is fixed.

Also covering the lanes around Faulkland

Beyond Faulkland we're frequently on jobs in Hemington (BA3), Norton St Philip (BA2), Shoscombe (BA2) and Kilmersdon (BA3) — so spares, follow-ups and annual services are straightforward.

Proof, paperwork and accountability

Local, family-run

Based at 24 Bristol Rd, Radstock — every job is run by the team that quoted it.

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Checkatrade 9.9/10

362+ verified reviews from real customers across BA and BS postcodes.

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

What you get, start to finish

Gas Safe registered engineers
Free no-obligation quotes
Smart heating controls fitted
Conversions (regular to combi)
Free written quote, no obligation
Local aftercare from a 3-mile base

Straight answers for Faulkland homeowners

How do we decide between a combi boiler and a boiler-plus-cylinder system?: It comes down to hot water demand and available space. A combi heats water on demand with no cylinder to fill, which suits smaller households and single-bathroom homes, while a system or regular boiler with a cylinder stores hot water and copes far better where two bathrooms or a bath and shower run at the same time.
Can you look over a quote I've already had from another company?: Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.
Is oil more expensive to run than mains gas?: Oil and gas prices both move with the wholesale market and neither is fixed, so a blanket answer isn't honest. What we can say is that a modern condensing oil boiler, correctly sized and commissioned, will run considerably more efficiently than an old non-condensing model — that efficiency gap usually matters more than the fuel choice itself.
How do you decide whether to repair or replace a boiler?: We weigh the age of the boiler, whether parts are still made for it, how many faults it's had recently, and its running efficiency against a like-for-like or upgraded replacement. If a straightforward part fixes it and the boiler's otherwise sound, we'll say so rather than push a new install you don't need.
Since Faulkland is so close to your base, can you offer more flexible slot timing?: Being close by does help us fit shorter jobs — like a service or a minor repair — into gaps between other bookings more easily than a longer round trip would allow. For a full installation the timescale is the same either way, since the work itself takes the same amount of time regardless of the drive.
Do you cover all of Faulkland?: Yes — every street in BA3 that falls under Faulkland, plus the lanes towards Hemington and Norton St Philip. We're 3 miles away in Radstock, so most jobs are reached in well under half an hour.

Booking work in Faulkland

Expect three things from gas boiler installation with us: a proper look at the property before any figure is given, a written quote that spells out what's included, and work carried out by a Gas Safe and OFTEC registered engineer who stands behind it. Gas work is signed off Gas Safe; oil work is signed off OFTEC. homes alongside small commercial and agricultural premises make up most enquiries from this postcode. Access is lane access, so parking, spoil removal and delivery timing get planned in advance.

07516 118198 All services in Faulkland

Local reference data

County: Somerset
Postcode district: BA3
Settlement type: village
Nearest classified road: A366
Distance from our base: 3 miles (Radstock, BA3)
Typical building stock: stone cottages and farms
Water hardness: very hard limestone water
Fuel availability: mains gas with off-grid pockets
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Hemington, Norton St Philip, Shoscombe, Kilmersdon

Detail that matters in Faulkland

Why very hard limestone water shortens boiler life around Faulkland

The limestone geology under Somerset gives Faulkland very hard limestone water, which drops calcium carbonate out of solution as soon as it's heated. Inside a combi's plate heat exchanger the gaps between plates are only a millimetre or two wide, so scale narrows the waterways long before it's visible anywhere else in the system. The first symptom is usually a hot tap that runs warm rather than hot, or a boiler that fires more often for the same demand. Left unchecked, scale insulates the exchanger from the burner, forces flue gases hotter, and can crack the exchanger from thermal stress. A scale reducer fitted on the mains feed, sized to the property's flow rate, is cheaper to install once than to replace a heat exchanger twice.

Oil tank de-sludging: why it's not optional

Oil sitting in a tank for years accumulates water from condensation and fine sediment that settles at the bottom, and over time this forms a sludge layer that can be drawn into the fuel line, particularly when the tank is nearly empty and the outlet pulls from lower in the tank than usual. Sludge blocks fine oil filters and burner nozzles, which shows up as burner lockouts or a boiler that won't fire cleanly rather than as an obvious tank problem. De-sludging drains and cleans the tank base without necessarily removing the whole tank, and it's worth doing when a tank is inherited with a property, before switching to a new boiler, or if lockouts recur despite the filter and nozzle being replaced. It's a preventative job that's cheaper done on schedule than after a burner failure it caused.

Being minutes away in Faulkland

Faulkland sits close enough to our Radstock base, just 3 miles via the A366, that a diagnostic visit or a return trip for a part doesn't add the delay it would on a job further afield. That's practically useful on jobs where a fault only shows itself once a boiler's been running for a while, or where a part needs collecting after an initial diagnosis rather than being carried on the off-chance. It doesn't change how the job itself is done — the same Gas Safe and OFTEC standards and the same commissioning paperwork apply regardless of distance — but it does mean less waiting between visits on multi-stage jobs like a full system upgrade that needs a survey, a flush, and an installation visit in sequence.

Radiator sizing after lowering the flow temperature

Running a boiler at a lower flow temperature — typically 55°C or below rather than the old default of 70-80°C — improves condensing efficiency measurably, but it also reduces the heat output of every radiator in the house, because a radiator's output falls roughly with the square of the temperature difference to the room. Radiators sized correctly for a 75°C flow can end up unable to heat the room properly at 55°C unless they're upsized or supplemented. We check each radiator against the lower design flow temperature before recommending it, and where a room falls short we look at whether a larger single panel, a double panel, or an additional radiator on that circuit closes the gap, rather than pushing the flow temperature back up and giving away the efficiency gain.

Heating where a home sits alongside commercial premises

Properties around Faulkland that combine living accommodation with an attached shop, workshop or other commercial space often need heating designed as genuinely separate zones with independent controls, since a shop's occupied hours and heating demand rarely match the flat or house above it. Where the two shared a single ageing system, splitting them onto separate zone valves — or, on a larger scale, separate boilers — stops one side subsidising or interfering with the other's heating schedule. Commercial space also sometimes falls under different servicing and safety-record obligations than the residential side, depending on how it's used, so it's worth establishing which parts of the building fall under which regime before assuming a single annual service covers everything.

Chimney liners for boilers using an existing flue

Where an older boiler used the property's original brick or stone chimney as its flue route, a replacement condensing boiler usually can't use the same masonry flue unlined, because the flue gases are cooler and wetter and will attack unprotected brickwork and mortar over time. A correctly specified stainless steel liner, sized to the boiler manufacturer's flue length and diameter tables, carries the flue gases safely and lets the existing chimney be reused rather than needing a new wall or roof penetration — often the only realistic option on a listed or solid-wall property in Faulkland where an external flue run isn't permitted. The liner has to be inspected and swept as part of ongoing servicing exactly as an open-fire flue would be, which is easy to overlook once it's hidden inside the chimney.

Chasing pipework into lime plaster and stone walls

Solid stone or cob walls finished in lime plaster, common in the older parts of Faulkland, behave very differently to modern plasterboard when a pipe run needs chasing in. Lime plaster is softer and more porous than gypsum, so cutting a neat, consistent chase without blowing the surface needs a slower hand and finer disc than a stud-wall job, and any repair has to be made good in a lime-based skim rather than modern filler, which can trap moisture behind it and cause the patch to fail. On solid stone we sometimes surface-mount pipework in painted conduit instead of chasing, particularly where the wall is a significant structural thickness and chasing would weaken it. Knowing which approach a wall needs before starting avoids expensive plaster damage.

Village lane access and van positioning for larger jobs

Village lanes around Faulkland are often single-track or tight two-way roads without dedicated off-street loading space, which affects how a larger job like a full system installation or an oil tank replacement is planned — the van needs somewhere to park close enough for repeated trips carrying equipment without blocking the lane for through traffic or farm vehicles. On a job involving a full radiator or pipework replacement, materials sometimes need staging over more than one visit rather than delivered all at once if there's nowhere secure to leave them on-site between visits. We check lane width and passing places when scheduling larger jobs in village locations, and plan van access and parking as part of the job rather than as an afterthought on the day.

Other boiler services in Faulkland

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote