How do we decide between a combi boiler and a boiler-plus-cylinder system?

It comes down to hot water demand and available space. A combi heats water on demand with no cylinder to fill, which suits smaller households and single-bathroom homes, while a system or regular boiler with a cylinder stores hot water and copes far better where two bathrooms or a bath and shower run at the same time.

Can your van get down our lane, or do we need to arrange something?

Most village lanes we work on are manageable in our vehicles, but if it's single-track, has a low bridge, or turning is tight, mention it when you book so we bring the right size van and allow extra time. It's rarely a reason to turn a job down, just something we plan around.

How does LPG heating differ from mains gas day to day?

An LPG boiler works the same way as a mains gas one day to day, but the gas is stored in a tank or cylinders on site and topped up by a supplier rather than piped in continuously. That means keeping an eye on tank levels and arranging deliveries, but appliance choice, controls, and servicing requirements are otherwise very similar.

What if a part for my existing boiler isn't available anymore?

Manufacturers stop stocking parts for discontinued models after a number of years, and once that happens a repair simply isn't possible even if the fault itself is minor. We'll confirm parts availability with the manufacturer before quoting a repair, and if it's a dead end we'll explain your replacement options honestly.

What does "commissioning" a boiler actually involve?

Commissioning is setting the boiler up correctly for the property rather than just switching it on: checking gas or oil pressure and flow rates, setting flow temperatures, testing safety devices, balancing the system, and completing the manufacturer's Benchmark checklist. Skipping this properly is one of the most common reasons warranty claims get refused later.

Do you cover all of Staverton?

Yes — every street in BA14 that falls under Staverton, plus the lanes towards Hilperton and Bradford on Avon. We're 11 miles away in Radstock, so most jobs are reached in well under half an hour.

Local Gas Boiler Installation for Staverton

Before quoting for gas boiler installation, we start with what's actually there: the existing pipework, the flue route, the water pressure and the age of what you've already got. Guesswork on a heating system leads to call-backs and wasted money, so a proper look at the property comes first. We're Gas Safe registered and OFTEC registered, based at 24 Bristol Road, Radstock BA3 3EE, and we size and specify jobs on what we find on site, not on assumptions. Planning constraints are usually light here, so external work is checked first. homes alongside small commercial and agricultural premises make up most enquiries from this postcode. In Staverton itself (BA14, Wiltshire) that usually means stone cottages and modern estates, roughly 11 miles from the workshop.

07516 118198 Ask about documentation

BA14 · Wiltshire · 11 mi from Radstock · B3105

Controls and cylinder layout typical of Staverton homes (BA14), gas boiler installation in Staverton (BA14) — hill top setting

Where else we work near Staverton

Beyond Staverton we're frequently on jobs in Hilperton (BA14), Bradford on Avon (BA15), Trowbridge (BA14) and Holt (BA14) — so spares, follow-ups and annual services are straightforward.

Proof, paperwork and accountability

Local, family-run

Based at 24 Bristol Rd, Radstock — every job is run by the team that quoted it.

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Checkatrade 9.9/10

362+ verified reviews from real customers across BA and BS postcodes.

Fixed written prices

No verbal-only quotes. You'll get the boiler model, controls and warranty in writing before we book.

Local conditions we plan around in BA14

Properties in this area sometimes sit alongside small commercial premises or agricultural buildings, which occasionally means slightly different considerations around flue positioning, noise from external plant, or shared access with a business next door. It's worth mentioning at the point of booking a survey if your property has any commercial neighbours or shared access, so we can check anything relevant before quoting rather than after. Water here is moderately hard water, so scale protection is specified accordingly. Access is lane access, so parking, spoil removal and delivery timing get planned in advance. Staverton is roughly 11 miles from our Radstock base via the B3105. Typical property stock here: stone cottages and modern estates. A meaningful share of properties around Staverton are off the gas grid, so oil boiler installs and tank swaps make up a fair part of what we do locally. When we quote gas boiler installation here we factor in flue routing, condensate fall and gas-supply pipe sizing before the price is fixed.

Scope of work, itemised

Gas Safe registered engineers
Free no-obligation quotes
Smart heating controls fitted
Conversions (regular to combi)
Free written quote, no obligation
Local aftercare from a 11-mile base

Questions before you book

How do we decide between a combi boiler and a boiler-plus-cylinder system?: It comes down to hot water demand and available space. A combi heats water on demand with no cylinder to fill, which suits smaller households and single-bathroom homes, while a system or regular boiler with a cylinder stores hot water and copes far better where two bathrooms or a bath and shower run at the same time.
Can your van get down our lane, or do we need to arrange something?: Most village lanes we work on are manageable in our vehicles, but if it's single-track, has a low bridge, or turning is tight, mention it when you book so we bring the right size van and allow extra time. It's rarely a reason to turn a job down, just something we plan around.
How does LPG heating differ from mains gas day to day?: An LPG boiler works the same way as a mains gas one day to day, but the gas is stored in a tank or cylinders on site and topped up by a supplier rather than piped in continuously. That means keeping an eye on tank levels and arranging deliveries, but appliance choice, controls, and servicing requirements are otherwise very similar.
What if a part for my existing boiler isn't available anymore?: Manufacturers stop stocking parts for discontinued models after a number of years, and once that happens a repair simply isn't possible even if the fault itself is minor. We'll confirm parts availability with the manufacturer before quoting a repair, and if it's a dead end we'll explain your replacement options honestly.
What does "commissioning" a boiler actually involve?: Commissioning is setting the boiler up correctly for the property rather than just switching it on: checking gas or oil pressure and flow rates, setting flow temperatures, testing safety devices, balancing the system, and completing the manufacturer's Benchmark checklist. Skipping this properly is one of the most common reasons warranty claims get refused later.
Do you cover all of Staverton?: Yes — every street in BA14 that falls under Staverton, plus the lanes towards Hilperton and Bradford on Avon. We're 11 miles away in Radstock, so most jobs are reached in well under half an hour.

Next step for Staverton

You can arrange a survey for gas boiler installation directly by calling 07516 118198 during Monday to Friday, 8:30am to 5pm, or by visiting us at 24 Bristol Road, Radstock BA3 3EE if that's easier. Either way, we'll take some initial details about the property before arranging a time to visit. We can usually pair the visit with other work in Hilperton to keep the trip efficient. Access is lane access, so parking, spoil removal and delivery timing get planned in advance. Mains gas covers much of the area, with off-grid pockets, which changes the appliance shortlist.

07516 118198 All services in Staverton

Staverton at a glance

County: Wiltshire
Postcode district: BA14
Settlement type: village
Nearest classified road: B3105
Distance from our base: 11 miles (Radstock, BA3)
Typical building stock: stone cottages and modern estates
Water hardness: moderately hard water
Fuel availability: mains gas with off-grid pockets
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Hilperton, Bradford on Avon, Trowbridge, Holt

Things we check around Staverton

Reaching properties off the main road network

Staverton is reached via the B3105, a B-road rather than a trunk route, which matters mainly for winter access and for confirming a delivery vehicle carrying a new oil tank or bulky equipment can realistically reach the property. We factor the actual route in when scheduling deliveries or larger installations, checking with the customer about any width, height or surface restrictions on the final approach rather than assuming a mapping app's route reflects what a loaded van can manage. It rarely changes the technical scope of a job, but it does affect how a visit is planned and timed, particularly for jobs needing a specific delivery slot to coincide with the installation date.

Nozzle replacement and baffle cleaning on oil burners

An oil burner's nozzle atomises fuel into a fine spray for combustion, and it wears from constant fuel flow at pressure, gradually changing the spray pattern away from the burner manufacturer's specification even before it visibly fails. A worn nozzle burns less cleanly, producing more soot that coats the heat exchanger's baffles, and a sooted heat exchanger loses efficiency in the same way scale does on a gas boiler's plates. Standard practice on an annual oil service is to replace the nozzle as a matter of course, rather than wait for a fault, and to remove and clean the baffles so the heat exchanger surfaces are exposed to combustion heat properly again. Skipping nozzle replacement to save a service visit's minor parts cost is a false economy against the fuel wasted by a poorly atomising burner.

Common boiler fault codes and what usually causes them

Most modern boilers display a fault code on the control panel when they lock out, and while the exact code differs between manufacturers, the underlying causes cluster into a small number of categories: low system pressure (often from a small leak or after bleeding radiators), ignition failure (a worn electrode, gas supply issue, or blocked condensate causing a safety shutdown), or a failed sensor reporting an implausible temperature reading. A condensate blockage or freeze specifically tends to show a distinct code from a genuine ignition fault, which is why checking the external condensate pipe for ice before calling out an engineer in a cold snap can sometimes resolve the issue without a visit at all. We ask for the exact fault code and any recent history — a bled radiator, a cold snap, a recent service — before attending, since it often narrows down the likely cause before we arrive.

Chimney liners for boilers using an existing flue

Where an older boiler used the property's original brick or stone chimney as its flue route, a replacement condensing boiler usually can't use the same masonry flue unlined, because the flue gases are cooler and wetter and will attack unprotected brickwork and mortar over time. A correctly specified stainless steel liner, sized to the boiler manufacturer's flue length and diameter tables, carries the flue gases safely and lets the existing chimney be reused rather than needing a new wall or roof penetration — often the only realistic option on a listed or solid-wall property in Staverton where an external flue run isn't permitted. The liner has to be inspected and swept as part of ongoing servicing exactly as an open-fire flue would be, which is easy to overlook once it's hidden inside the chimney.

Radiator sizing after lowering the flow temperature

Running a boiler at a lower flow temperature — typically 55°C or below rather than the old default of 70-80°C — improves condensing efficiency measurably, but it also reduces the heat output of every radiator in the house, because a radiator's output falls roughly with the square of the temperature difference to the room. Radiators sized correctly for a 75°C flow can end up unable to heat the room properly at 55°C unless they're upsized or supplemented. We check each radiator against the lower design flow temperature before recommending it, and where a room falls short we look at whether a larger single panel, a double panel, or an additional radiator on that circuit closes the gap, rather than pushing the flow temperature back up and giving away the efficiency gain.

Planning a visit out to Staverton

At 11 miles from Radstock via the B3105, a job in Staverton is planned as a full visit rather than a quick call-back, which is why we ask more detail up front — model numbers, symptoms, access notes — so the first visit is more likely to be the one that resolves the issue rather than the one that diagnoses it. For multi-stage work such as a full boiler and system upgrade, we sequence the survey, any preparatory work and the installation to minimise separate trips where the job allows it. It doesn't affect the standard of work or the paperwork completed on-site, but it's a reasonable practical difference from a job five minutes from the workshop, and we're upfront about it when scheduling.

Staverton's place within the wider Wiltshire area we cover

Staverton is one of several neighbourhoods we work in around the wider area, and while the postcode district and general water hardness and building stock trends are shared with the surrounding district, the specific street-level access, parking and property type still varies enough locally that we treat each visit on its own facts rather than applying a generic area answer. Nearby areas we also cover include Hilperton, Bradford on Avon and Trowbridge, which is relevant mainly where a customer wants comparable jobs referenced or where a single visit can sensibly cover more than one nearby property in the same trip. The underlying trade standards — Gas Safe, OFTEC, correct commissioning — don't vary by neighbourhood, only the practical details of the job do.

Heating where a home sits alongside commercial premises

Properties around Staverton that combine living accommodation with an attached shop, workshop or other commercial space often need heating designed as genuinely separate zones with independent controls, since a shop's occupied hours and heating demand rarely match the flat or house above it. Where the two shared a single ageing system, splitting them onto separate zone valves — or, on a larger scale, separate boilers — stops one side subsidising or interfering with the other's heating schedule. Commercial space also sometimes falls under different servicing and safety-record obligations than the residential side, depending on how it's used, so it's worth establishing which parts of the building fall under which regime before assuming a single annual service covers everything.

Other boiler services in Staverton

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote