We run a holiday let — do the same gas safety rules apply as a standard rental?

Yes, holiday lets fall under the same landlord gas safety duty as any other let property — an annual CP12 from a Gas Safe registered engineer is required, and it's worth timing the visit for a gap between bookings rather than trying to fit it around guests, which we're happy to help plan around.

Can you look over a quote I've already had from another company?

Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.

Do you cover South Stoke?

Yes. South Stoke is 8 miles from our workshop at 24 Bristol Road, Radstock BA3 3EE, reached via the B3110, and it's a regular part of our working area. We're Gas Safe and OFTEC registered, so we cover both mains gas and oil work out here without treating it as a special trip.

Is oil more expensive to run than mains gas?

Oil and gas prices both move with the wholesale market and neither is fixed, so a blanket answer isn't honest. What we can say is that a modern condensing oil boiler, correctly sized and commissioned, will run considerably more efficiently than an old non-condensing model — that efficiency gap usually matters more than the fuel choice itself.

What are your opening hours, and can you help out of hours?

Our published hours are Monday to Friday, 8:30am to 5pm, and that's when the phones are answered and jobs are booked. We're honest that we don't run a round-the-clock emergency line, so if you're planning ahead, call during those hours on 07516 118198 and we'll get you booked in.

Do we need planning permission for a new boiler flue on a listed or conservation-area property?

If the property is listed, Listed Building Consent can be needed for anything altering its appearance, including a new external flue terminal, even where the work itself would normally be permitted development. In conservation areas like parts of South Stoke's setting, flue position and visibility from the street can also come under scrutiny. We flag this at survey rather than after ordering the boiler.

Oil Boiler Installers in South Stoke

When you're comparing tradespeople for oil boiler installation, it's worth checking registration before price: Gas Safe for mains gas work, OFTEC for oil, and manufacturer accreditation if a specific guarantee matters to you. We hold all three — Gas Safe, OFTEC and Worcester Bosch Accredited Installer status — and work from 24 Bristol Road, Radstock BA3 3EE, so you can check us against whatever criteria you're using to shortlist. Access is lane access, so parking, spoil removal and delivery timing get planned in advance. Mains gas covers much of the area, with off-grid pockets, which changes the appliance shortlist. In South Stoke itself (BA2, Somerset) that usually means stone village cottages, roughly 8 miles from the workshop.

07516 118198 Ask about the guarantee

BA2 · Somerset · 8 mi from Radstock · B3110

Gas-fired appliance serving a level property near South Stoke, oil boiler installation in South Stoke (BA2) — lane access access

How we run oil boiler installation on site

OFTEC trained & registered
Internal & external oil boilers
Oil tank replacements
Worcester Greenstar & Grant Vortex
Free written quote, no obligation
Local aftercare from a 8-mile base

Where else we work near South Stoke

Beyond South Stoke we're frequently on jobs in Combe Down (BA2), Odd Down (BA2), Wellow (BA2) and Combe Hay (BA2) — so spares, follow-ups and annual services are straightforward.

Qualifications behind the work

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

Checkatrade 9.9/10

362+ verified reviews from real customers across BA and BS postcodes.

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Fixed written prices

No verbal-only quotes. You'll get the boiler model, controls and warranty in writing before we book.

What the buildings in South Stoke change about the job

Water here runs off carboniferous limestone and Jurassic oolite, which makes it very hard by national standards. Hard water accelerates scale build-up inside heat exchangers, cylinders and pipework, which shortens the working life of components that aren't protected against it. On jobs in this area we factor scale protection into the specification rather than treating it as an optional extra, because the difference between a protected and unprotected system shows up within a few years, not decades. It's a genuine local variable, not generic sales advice, and it applies whether the property is on mains gas or oil. Access is lane access, so parking, spoil removal and delivery timing get planned in advance. Nearest neighbours on our round are Combe Down, Odd Down, Wellow. South Stoke is roughly 8 miles from our Radstock base via the B3110. Typical property stock here: stone village cottages. South Stoke sits in the Somerset BA2 postcode and is part of our weekly run, so local response is quick. For oil work we look at the tank's age, bund condition, fire valve and fuel-line route as part of the survey — not as an afterthought.

Common queries, answered honestly

We run a holiday let — do the same gas safety rules apply as a standard rental?: Yes, holiday lets fall under the same landlord gas safety duty as any other let property — an annual CP12 from a Gas Safe registered engineer is required, and it's worth timing the visit for a gap between bookings rather than trying to fit it around guests, which we're happy to help plan around.
Can you look over a quote I've already had from another company?: Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.
Do you cover South Stoke?: Yes. South Stoke is 8 miles from our workshop at 24 Bristol Road, Radstock BA3 3EE, reached via the B3110, and it's a regular part of our working area. We're Gas Safe and OFTEC registered, so we cover both mains gas and oil work out here without treating it as a special trip.
Is oil more expensive to run than mains gas?: Oil and gas prices both move with the wholesale market and neither is fixed, so a blanket answer isn't honest. What we can say is that a modern condensing oil boiler, correctly sized and commissioned, will run considerably more efficiently than an old non-condensing model — that efficiency gap usually matters more than the fuel choice itself.
What are your opening hours, and can you help out of hours?: Our published hours are Monday to Friday, 8:30am to 5pm, and that's when the phones are answered and jobs are booked. We're honest that we don't run a round-the-clock emergency line, so if you're planning ahead, call during those hours on 07516 118198 and we'll get you booked in.
Do we need planning permission for a new boiler flue on a listed or conservation-area property?: If the property is listed, Listed Building Consent can be needed for anything altering its appearance, including a new external flue terminal, even where the work itself would normally be permitted development. In conservation areas like parts of South Stoke's setting, flue position and visibility from the street can also come under scrutiny. We flag this at survey rather than after ordering the boiler.

How to get this priced

If you're still deciding whether oil boiler installation is the right move for your property, a site visit and honest conversation costs you nothing but time. We'll tell you if we think repair is a better option than replacement, or if the job is more or less involved than you expected. Send the appliance make, model and any fault code and you get a straight answer, not a sales script. Conservation and listed constraints apply to parts of the area, so external work is checked first. Terrain is level, which matters for condensate runs and tank siting.

07516 118198 All services in South Stoke

Area data we work from

County: Somerset
Postcode district: BA2
Settlement type: village
Nearest classified road: B3110
Distance from our base: 8 miles (Radstock, BA3)
Typical building stock: stone village cottages
Water hardness: very hard limestone water
Fuel availability: mains gas with off-grid pockets
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Combe Down, Odd Down, Wellow, Combe Hay

Practical considerations across BA2

Low-loss headers on larger or multi-zone systems

On a system with several heating zones or a boiler oversized relative to any single zone's flow requirement, a low-loss header hydraulically separates the boiler's primary circuit from the secondary zone circuits, so each side can run its own pump and flow rate without one interfering with the other. Without it, a zone valve closing on a multi-zone system can starve the boiler of flow or force excessive pump pressure through the remaining open zones. It's most relevant on larger properties or ones with commercial premises attached, where several distinct heating circuits — perhaps a shop unit and a flat above — share one heat source. Getting the header sized to the boiler's actual flow rate, not just fitted as standard, is what makes it work rather than just adding another connection.

Plume management kits for restricted flue positions

Where the ideal, shortest flue route would discharge too close to a boundary, a window, or onto a neighbouring property — a common constraint on tight plots in South Stoke — a plume management kit extends the flue's discharge point away from the boiler's own wall penetration, directing the visible water vapour plume and flue gases to a compliant location instead. It adds ductwork and sometimes a small additional fan to overcome the extra resistance, and it has to be specified against the specific boiler's approved kit range rather than improvised, since flue certification only covers tested combinations. It's a legitimate way to fit a boiler on a plot where the compliant flue route and the sensible boiler location aren't the same wall, without compromising on clearances to solve it.

Signs a boiler repair is no longer the right call

A boiler that's failing repeatedly, needing a different part replaced every service, or over roughly ten to fifteen years old is approaching the point where continued repair costs more over time than replacement, particularly once a heat exchanger — the most expensive single part — starts to show signs of failure through leaks or reduced output. Efficiency is the other half of the calculation: an older non-condensing boiler running at 70-80% efficiency against a modern condensing combi at over 90% means a meaningful chunk of every unit of fuel burned in the old boiler is simply lost up the flue. We give a straight answer on repair versus replace based on the fault found and the boiler's age and condition, rather than defaulting to whichever is more profitable to us on the day.

Electronic and physical scale reducers compared

In very hard limestone water areas like South Stoke, a scale reducer fitted on the boiler's cold feed protects the heat exchanger without the ongoing salt and drainage requirements of a full water softener. Physical scale reducers use a polyphosphate or template-assisted crystallisation cartridge that alters how calcium carbonate crystallises so it's less likely to adhere to hot surfaces; electronic and electromagnetic devices claim a similar effect without a cartridge to replace, though the evidence base for electronic types is weaker and more inconsistent than for physical media. Manufacturers including Worcester Bosch now specify a scale reducer or softener as a condition of extended guarantees in hard water areas, so the choice affects warranty validity as well as long-term performance, not just descale frequency.

Nozzle replacement and baffle cleaning on oil burners

An oil burner's nozzle atomises fuel into a fine spray for combustion, and it wears from constant fuel flow at pressure, gradually changing the spray pattern away from the burner manufacturer's specification even before it visibly fails. A worn nozzle burns less cleanly, producing more soot that coats the heat exchanger's baffles, and a sooted heat exchanger loses efficiency in the same way scale does on a gas boiler's plates. Standard practice on an annual oil service is to replace the nozzle as a matter of course, rather than wait for a fault, and to remove and clean the baffles so the heat exchanger surfaces are exposed to combustion heat properly again. Skipping nozzle replacement to save a service visit's minor parts cost is a false economy against the fuel wasted by a poorly atomising burner.

Chimney liners for boilers using an existing flue

Where an older boiler used the property's original brick or stone chimney as its flue route, a replacement condensing boiler usually can't use the same masonry flue unlined, because the flue gases are cooler and wetter and will attack unprotected brickwork and mortar over time. A correctly specified stainless steel liner, sized to the boiler manufacturer's flue length and diameter tables, carries the flue gases safely and lets the existing chimney be reused rather than needing a new wall or roof penetration — often the only realistic option on a listed or solid-wall property in South Stoke where an external flue run isn't permitted. The liner has to be inspected and swept as part of ongoing servicing exactly as an open-fire flue would be, which is easy to overlook once it's hidden inside the chimney.

Village lane access and van positioning for larger jobs

Village lanes around South Stoke are often single-track or tight two-way roads without dedicated off-street loading space, which affects how a larger job like a full system installation or an oil tank replacement is planned — the van needs somewhere to park close enough for repeated trips carrying equipment without blocking the lane for through traffic or farm vehicles. On a job involving a full radiator or pipework replacement, materials sometimes need staging over more than one visit rather than delivered all at once if there's nowhere secure to leave them on-site between visits. We check lane width and passing places when scheduling larger jobs in village locations, and plan van access and parking as part of the job rather than as an afterthought on the day.

How a condensing boiler recovers extra heat

A condensing boiler passes flue gases through a secondary heat exchanger before they leave the flue, extracting additional heat by condensing water vapour in the exhaust back into liquid, which is expelled as the mildly acidic condensate water down the drain. This is why every condensing boiler needs a condensate drainage route as part of its installation, unlike older non-condensing boilers, which simply vented hot dry gas straight out. The efficiency benefit only fully materialises when the boiler is actually condensing regularly, which needs a return water temperature low enough — generally below 55°C — for water vapour to condense in the first place. A condensing boiler run permanently at a high flow temperature can spend much of its time not actually condensing, which is one of the main reasons flow temperature settings matter as much as the boiler model chosen.

Pumped-oil versus gravity feed: does it matter?

Older oil systems sometimes still rely on gravity feed, where the tank sits higher than the burner and oil flows down to it under its own weight; a pumped system uses the burner's internal pump to draw oil up from a tank at any level, including below the boiler. Gravity feed limits where a tank can be sited and is more prone to airlocks if the line runs dry, while a pumped system is more flexible on tank position but needs the pipe run and lift height kept within the burner pump's rated capacity — usually no more than a few metres of lift and a set maximum run length. When we replace an oil boiler we check which type the existing tank and pipework support before assuming a straight swap, because a tank sited for gravity feed may need repositioning or a different pump to suit a modern burner.

Other boiler services in South Stoke

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote