Will the new boiler work properly with our existing radiators?

Not always without checking. Modern condensing boilers run most efficiently at lower flow temperatures, and radiators originally sized for an old, hotter-running boiler can end up struggling to heat a room adequately at those lower temperatures. We check radiator sizing against a heat loss calculation and flag any that are undersized for the room before installing.

Can you look over a quote I've already had from another company?

Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.

We run a holiday let — do the same gas safety rules apply as a standard rental?

Yes, holiday lets fall under the same landlord gas safety duty as any other let property — an annual CP12 from a Gas Safe registered engineer is required, and it's worth timing the visit for a gap between bookings rather than trying to fit it around guests, which we're happy to help plan around.

What support do I get after the install is finished?

Once commissioning's complete we talk you through the controls, leave the paperwork, and register the manufacturer warranty on your behalf. If anything doesn't feel right in the first few weeks — a fault code, an odd noise, a control setting you're unsure of — call us during office hours and we'll talk it through or come back out.

What's an unvented cylinder and does it need special installation rules?

An unvented cylinder stores mains-pressure hot water without a cold water tank in the loft, giving strong pressure at every outlet. Building Regulations require it to be fitted and commissioned by someone holding a specific unvented cylinder qualification (which we hold), including fitting the correct safety valves, because an incorrectly installed unvented cylinder is a pressure vessel hazard.

Will you come out to a village like Butleigh?

Butleigh is part of our core patch (14 miles from base via the unclassified). Same-week site visits and quick callbacks are normal.

Butleigh Oil Tank Replacement

Oil Tank Replacement sits alongside the wider servicing cycle a heating system goes through over its life: commissioning, annual checks, and eventually replacement once repairs stop making sense. Thinking about where you are in that cycle helps decide whether now is the right time to act. We're Gas Safe registered and OFTEC registered, based at 24 Bristol Road, Radstock BA3 3EE, and happy to talk through where your system currently sits before recommending anything. Typical era of build is mixed-cottage, which affects existing pipework and system cleanliness.

07516 118198 Call now

BA6 · Somerset · 14 mi from Radstock · unclassified

Oil Tank Replacement on a village property 14 miles from Radstock — lane access access

Local conditions we plan around in BA6

Properties out this way are commonly off the mains gas network, which means oil is often the realistic option rather than a fallback. That changes the shape of the job: tank location and condition, delivery vehicle access, and how the boiler and tank relate to each other on site all need checking before a quote can be accurate. We're OFTEC registered as well as Gas Safe registered, so oil-fired boiler work, tank considerations and servicing are handled properly rather than as a secondary service alongside gas. Terrain is level, which matters for condensate runs and tank siting. Butleigh is roughly 14 miles from our Radstock base via the unclassified. Typical property stock here: stone cottages and farmhouses. A meaningful share of properties around Butleigh are off the gas grid, so oil boiler installs and tank swaps make up a fair part of what we do locally. Repair calls in Butleigh usually get a same-week visit, with most common faults fixed on the first attempt.

Registrations and how work is signed off

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Checkatrade 9.9/10

362+ verified reviews from real customers across BA and BS postcodes.

Local, family-run

Based at 24 Bristol Rd, Radstock — every job is run by the team that quoted it.

Also covering the lanes around Butleigh

Beyond Butleigh we're frequently on jobs in Baltonsborough (BA6), Walton (BA16), Glastonbury (BA6) and West Pennard (BA6) — so spares, follow-ups and annual services are straightforward.

The work, step by step

Bunded plastic and steel tanks supplied
Base preparation and safe siting distances
New supply line, filter and fire valve
Old tank drained and removed
Free written quote, no obligation
Local aftercare from a 14-mile base

Questions before you book

Will the new boiler work properly with our existing radiators?: Not always without checking. Modern condensing boilers run most efficiently at lower flow temperatures, and radiators originally sized for an old, hotter-running boiler can end up struggling to heat a room adequately at those lower temperatures. We check radiator sizing against a heat loss calculation and flag any that are undersized for the room before installing.
Can you look over a quote I've already had from another company?: Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.
We run a holiday let — do the same gas safety rules apply as a standard rental?: Yes, holiday lets fall under the same landlord gas safety duty as any other let property — an annual CP12 from a Gas Safe registered engineer is required, and it's worth timing the visit for a gap between bookings rather than trying to fit it around guests, which we're happy to help plan around.
What support do I get after the install is finished?: Once commissioning's complete we talk you through the controls, leave the paperwork, and register the manufacturer warranty on your behalf. If anything doesn't feel right in the first few weeks — a fault code, an odd noise, a control setting you're unsure of — call us during office hours and we'll talk it through or come back out.
What's an unvented cylinder and does it need special installation rules?: An unvented cylinder stores mains-pressure hot water without a cold water tank in the loft, giving strong pressure at every outlet. Building Regulations require it to be fitted and commissioned by someone holding a specific unvented cylinder qualification (which we hold), including fitting the correct safety valves, because an incorrectly installed unvented cylinder is a pressure vessel hazard.
Will you come out to a village like Butleigh?: Butleigh is part of our core patch (14 miles from base via the unclassified). Same-week site visits and quick callbacks are normal.

Where to go from here

Getting in touch about oil tank replacement is straightforward: call 07516 118198 within our normal working hours, Monday to Friday, 8:30am to 5pm, describe the property and what you need, and we'll talk through whether a survey makes sense as the next step. A written quote follows the survey — no pressure, and no charge for the Butleigh visit. Typical era of build is mixed-cottage, which affects existing pipework and system cleanliness.

07516 118198 All services in Butleigh

The factual picture in Butleigh

County: Somerset
Postcode district: BA6
Settlement type: village
Nearest classified road: unclassified
Distance from our base: 14 miles (Radstock, BA3)
Typical building stock: stone cottages and farmhouses
Water hardness: moderately hard water
Fuel availability: off-grid oil and LPG common
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Baltonsborough, Walton, Glastonbury, West Pennard

Things we check around Butleigh

Choosing a boiler location that satisfies both planning and practicality in Butleigh

On a property within a conservation area, AONB or World Heritage designation, the boiler's physical location is often decided as much by the acceptable flue route as by where the homeowner would naturally put it — a kitchen wall facing the street may need ruling out even before considering pipe run length, simply because the flue outlet would be visible from a protected streetscape. Working back from an acceptable flue position to find a viable boiler location sometimes means a longer pipework run through the property than would otherwise be chosen, adding to the job's cost and complexity. We assess planning constraints on the flue before finalising the boiler's proposed location, rather than picking the location first and discovering the flue route is unacceptable afterwards.

Chasing pipework into lime plaster and stone walls

Solid stone or cob walls finished in lime plaster, common in the older parts of Butleigh, behave very differently to modern plasterboard when a pipe run needs chasing in. Lime plaster is softer and more porous than gypsum, so cutting a neat, consistent chase without blowing the surface needs a slower hand and finer disc than a stud-wall job, and any repair has to be made good in a lime-based skim rather than modern filler, which can trap moisture behind it and cause the patch to fail. On solid stone we sometimes surface-mount pipework in painted conduit instead of chasing, particularly where the wall is a significant structural thickness and chasing would weaken it. Knowing which approach a wall needs before starting avoids expensive plaster damage.

Condensate soakaways where there's no convenient drain

Properties without a nearby internal waste connection or external gully for the boiler's condensate — common on rural plots around Butleigh where the nearest drain run is a long way from the boiler's location — sometimes need a dedicated condensate soakaway instead. This is a small pit filled with granular material that the condensate, which is mildly acidic, can disperse into gradually rather than running to a drain at all. Sizing and siting it correctly matters: it needs to be far enough from foundations and sited where the local ground can actually absorb the modest but steady volume a boiler produces, particularly over a long heating season. Where ground conditions make a soakaway unreliable, running a longer insulated pipe to a proper drainage connection is usually the safer long-term choice even though it's more work to install.

Choosing between oil, LPG and electric off the gas grid

Properties around Butleigh without a mains gas connection have a genuine choice between oil, bulk LPG and direct electric heating (or a heat pump), and the right answer depends on more than fuel price alone. Oil needs tank space, safe access for tanker delivery and the bunding/fire-valve provisions covered elsewhere, but gives strong, controllable heat output well suited to older, harder-to-heat stone properties. LPG suits households wanting gas-style controllability without oil's storage and burner maintenance, at a generally higher unit cost. A heat pump works best paired with good insulation and lower flow temperature emitters, and suits a property being upgraded rather than one where radiators and insulation are staying as they are. We look at the specific building's insulation, radiator sizing and available space before recommending a fuel switch rather than assuming one option suits every off-grid property.

Single-pipe circuits in older stone cottages

A lot of the stone cottages and farmhouses around Butleigh were plumbed decades ago on a single-pipe gravity circuit, where each radiator draws from and returns to the same loop rather than having its own flow and return. It works, but radiators furthest from the boiler receive water that's already cooled after giving up heat to the ones before it, so the far end of the house is always the coldest. Converting to a two-pipe layout means new pipe runs, which in a stone cottage often means chasing lime plaster or lifting flagstones — not a trivial job. Where a full rewire of the pipework isn't wanted, we sometimes improve balance instead by oversizing the radiators nearest the end of the run and fitting TRVs to hold back the ones nearest the boiler.

Reaching properties off the main road network

Butleigh is reached via the unclassified, an unclassified road rather than a numbered route, which matters mainly for winter access and for confirming a delivery vehicle carrying a new oil tank or bulky equipment can realistically reach the property. We factor the actual route in when scheduling deliveries or larger installations, checking with the customer about any width, height or surface restrictions on the final approach rather than assuming a mapping app's route reflects what a loaded van can manage. It rarely changes the technical scope of a job, but it does affect how a visit is planned and timed, particularly for jobs needing a specific delivery slot to coincide with the installation date.

Heating where a home sits alongside commercial premises

Properties around Butleigh that combine living accommodation with an attached shop, workshop or other commercial space often need heating designed as genuinely separate zones with independent controls, since a shop's occupied hours and heating demand rarely match the flat or house above it. Where the two shared a single ageing system, splitting them onto separate zone valves — or, on a larger scale, separate boilers — stops one side subsidising or interfering with the other's heating schedule. Commercial space also sometimes falls under different servicing and safety-record obligations than the residential side, depending on how it's used, so it's worth establishing which parts of the building fall under which regime before assuming a single annual service covers everything.

Wood-burning stoves with a back boiler alongside a main boiler

Some older rural properties around Butleigh run a wood-burning stove with a back boiler feeding heat into the same central heating circuit as an oil or gas boiler, usually through a thermal store or a cylinder with two coils. Getting this combination to work safely means the stove's back boiler circuit has its own means of dissipating heat if the pump fails or a valve closes while the stove is still burning — a stove can't simply be switched off the way a boiler can if its heat has nowhere to go, so a gravity-fed safety circuit or heat leak radiator is normally required. It's a more involved design than a single-boiler system and needs planning at the point either appliance is replaced, not treated as an afterthought once the new boiler is already fitted.

Other boiler services in Butleigh

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote