What's a CP12 and do I need one as a landlord?

A CP12 (Landlord Gas Safety Record) confirms every gas appliance in a rented property has passed an annual safety check by a Gas Safe registered engineer. It's a legal requirement before letting and at each renewal, a copy has to go to tenants, and it needs to be renewed every 12 months without a gap.

Can you look over a quote I've already had from another company?

Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.

How often should a boiler actually be serviced?

Once a year is the standard recommendation from every manufacturer, and most warranty terms make it a condition rather than a suggestion — miss a year and a claim can be refused even if the fault is unrelated. Landlords have a separate legal duty to have gas appliances checked annually regardless of warranty terms.

What's the difference between a power flush and a chemical flush?

A chemical flush circulates a cleaning agent through the existing system to loosen light debris, while a power flush uses a pump to force water at higher velocity and reversed direction through radiators and pipework to shift heavier sludge. We usually recommend the more thorough power flush before connecting a new boiler to an older system.

Is a boiler install a noisy, disruptive job?

There's unavoidable noise — drilling for the flue, pipework, sometimes moving a cylinder — but a straightforward swap is usually done within a working day with the mess kept to the immediate work area. We dust-sheet the route in and out and clear away pipe offcuts and old parts before we leave.

We're a home attached to or near a small business premises — do you cover that kind of property?

Where the heating system is a standard domestic boiler serving living accommodation, it's within our normal scope even if it sits next to or above a shop or workshop, which is a common layout around Swainswick. Fully commercial systems and appliances are a different scope, so we'd confirm exactly what's being asked at enquiry stage.

Oil Tank Replacement — Swainswick (BA1)

Getting quotes for oil tank replacement can feel like a gamble when you don't know the trade. You want someone who turns up when they say they will, explains what they're doing, and leaves you with a system you understand. That's the standard we work to from 24 Bristol Road, Radstock BA3 3EE. We're Gas Safe registered, OFTEC registered and a Worcester Bosch Accredited Installer, so the paperwork and the workmanship both hold up to scrutiny. homes alongside small commercial and agricultural premises make up most enquiries from this postcode.

07516 118198 Ask about the guarantee

BA1 · Somerset · 10 mi from Radstock · A46

Gas-fired appliance serving a level property near Swainswick — Somerset

Neighbouring Somerset areas we serve

Beyond Swainswick we're frequently on jobs in Bath (BA1), Batheaston (BA1), Lansdown (BA1) and Larkhall (BA1) — so spares, follow-ups and annual services are straightforward.

Registrations and how work is signed off

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

Checkatrade 9.9/10

362+ verified reviews from real customers across BA and BS postcodes.

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

Included as standard in Swainswick

Bunded plastic and steel tanks supplied
Base preparation and safe siting distances
New supply line, filter and fire valve
Old tank drained and removed
Free written quote, no obligation
Local aftercare from a 10-mile base

What the buildings in Swainswick change about the job

Water here runs off carboniferous limestone and Jurassic oolite, which makes it very hard by national standards. Hard water accelerates scale build-up inside heat exchangers, cylinders and pipework, which shortens the working life of components that aren't protected against it. On jobs in this area we factor scale protection into the specification rather than treating it as an optional extra, because the difference between a protected and unprotected system shows up within a few years, not decades. It's a genuine local variable, not generic sales advice, and it applies whether the property is on mains gas or oil. Nearest neighbours on our round are Bath, Batheaston, Lansdown. Swainswick is roughly 10 miles from our Radstock base via the A46. Typical property stock here: rural farmsteads and cottages. Swainswick sits in the Somerset BA1 postcode and is part of our weekly run, so local response is quick. Repair calls in Swainswick usually get a same-week visit, with most common faults fixed on the first attempt.

Oil Tank Replacement FAQs for BA1

What's a CP12 and do I need one as a landlord?: A CP12 (Landlord Gas Safety Record) confirms every gas appliance in a rented property has passed an annual safety check by a Gas Safe registered engineer. It's a legal requirement before letting and at each renewal, a copy has to go to tenants, and it needs to be renewed every 12 months without a gap.
Can you look over a quote I've already had from another company?: Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.
How often should a boiler actually be serviced?: Once a year is the standard recommendation from every manufacturer, and most warranty terms make it a condition rather than a suggestion — miss a year and a claim can be refused even if the fault is unrelated. Landlords have a separate legal duty to have gas appliances checked annually regardless of warranty terms.
What's the difference between a power flush and a chemical flush?: A chemical flush circulates a cleaning agent through the existing system to loosen light debris, while a power flush uses a pump to force water at higher velocity and reversed direction through radiators and pipework to shift heavier sludge. We usually recommend the more thorough power flush before connecting a new boiler to an older system.
Is a boiler install a noisy, disruptive job?: There's unavoidable noise — drilling for the flue, pipework, sometimes moving a cylinder — but a straightforward swap is usually done within a working day with the mess kept to the immediate work area. We dust-sheet the route in and out and clear away pipe offcuts and old parts before we leave.
We're a home attached to or near a small business premises — do you cover that kind of property?: Where the heating system is a standard domestic boiler serving living accommodation, it's within our normal scope even if it sits next to or above a shop or workshop, which is a common layout around Swainswick. Fully commercial systems and appliances are a different scope, so we'd confirm exactly what's being asked at enquiry stage.

Booking work in Swainswick

If oil tank replacement is something you're looking into, the simplest next step is a call on 07516 118198 during our normal hours, Monday to Friday, 8:30am to 5pm. Tell us a bit about the property and what's prompted the enquiry, and we'll take it from there. Photos of the existing setup speed up pricing for village properties like these. Water here is very hard limestone water, so scale protection is specified accordingly.

07516 118198 All services in Swainswick

Swainswick at a glance

County: Somerset
Postcode district: BA1
Settlement type: village
Nearest classified road: A46
Distance from our base: 10 miles (Radstock, BA3)
Typical building stock: rural farmsteads and cottages
Water hardness: very hard limestone water
Fuel availability: mains gas with off-grid pockets
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Bath, Batheaston, Lansdown, Larkhall

Practical considerations across BA1

Condensate soakaways where there's no convenient drain

Properties without a nearby internal waste connection or external gully for the boiler's condensate — common on rural plots around Swainswick where the nearest drain run is a long way from the boiler's location — sometimes need a dedicated condensate soakaway instead. This is a small pit filled with granular material that the condensate, which is mildly acidic, can disperse into gradually rather than running to a drain at all. Sizing and siting it correctly matters: it needs to be far enough from foundations and sited where the local ground can actually absorb the modest but steady volume a boiler produces, particularly over a long heating season. Where ground conditions make a soakaway unreliable, running a longer insulated pipe to a proper drainage connection is usually the safer long-term choice even though it's more work to install.

Chasing pipework into lime plaster and stone walls

Solid stone or cob walls finished in lime plaster, common in the older parts of Swainswick, behave very differently to modern plasterboard when a pipe run needs chasing in. Lime plaster is softer and more porous than gypsum, so cutting a neat, consistent chase without blowing the surface needs a slower hand and finer disc than a stud-wall job, and any repair has to be made good in a lime-based skim rather than modern filler, which can trap moisture behind it and cause the patch to fail. On solid stone we sometimes surface-mount pipework in painted conduit instead of chasing, particularly where the wall is a significant structural thickness and chasing would weaken it. Knowing which approach a wall needs before starting avoids expensive plaster damage.

Wood-burning stoves with a back boiler alongside a main boiler

Some older rural properties around Swainswick run a wood-burning stove with a back boiler feeding heat into the same central heating circuit as an oil or gas boiler, usually through a thermal store or a cylinder with two coils. Getting this combination to work safely means the stove's back boiler circuit has its own means of dissipating heat if the pump fails or a valve closes while the stove is still burning — a stove can't simply be switched off the way a boiler can if its heat has nowhere to go, so a gravity-fed safety circuit or heat leak radiator is normally required. It's a more involved design than a single-boiler system and needs planning at the point either appliance is replaced, not treated as an afterthought once the new boiler is already fitted.

Pumped-oil versus gravity feed: does it matter?

Older oil systems sometimes still rely on gravity feed, where the tank sits higher than the burner and oil flows down to it under its own weight; a pumped system uses the burner's internal pump to draw oil up from a tank at any level, including below the boiler. Gravity feed limits where a tank can be sited and is more prone to airlocks if the line runs dry, while a pumped system is more flexible on tank position but needs the pipe run and lift height kept within the burner pump's rated capacity — usually no more than a few metres of lift and a set maximum run length. When we replace an oil boiler we check which type the existing tank and pipework support before assuming a straight swap, because a tank sited for gravity feed may need repositioning or a different pump to suit a modern burner.

Oil tank de-sludging: why it's not optional

Oil sitting in a tank for years accumulates water from condensation and fine sediment that settles at the bottom, and over time this forms a sludge layer that can be drawn into the fuel line, particularly when the tank is nearly empty and the outlet pulls from lower in the tank than usual. Sludge blocks fine oil filters and burner nozzles, which shows up as burner lockouts or a boiler that won't fire cleanly rather than as an obvious tank problem. De-sludging drains and cleans the tank base without necessarily removing the whole tank, and it's worth doing when a tank is inherited with a property, before switching to a new boiler, or if lockouts recur despite the filter and nozzle being replaced. It's a preventative job that's cheaper done on schedule than after a burner failure it caused.

Low-loss headers on larger or multi-zone systems

On a system with several heating zones or a boiler oversized relative to any single zone's flow requirement, a low-loss header hydraulically separates the boiler's primary circuit from the secondary zone circuits, so each side can run its own pump and flow rate without one interfering with the other. Without it, a zone valve closing on a multi-zone system can starve the boiler of flow or force excessive pump pressure through the remaining open zones. It's most relevant on larger properties or ones with commercial premises attached, where several distinct heating circuits — perhaps a shop unit and a flat above — share one heat source. Getting the header sized to the boiler's actual flow rate, not just fitted as standard, is what makes it work rather than just adding another connection.

Nozzle replacement and baffle cleaning on oil burners

An oil burner's nozzle atomises fuel into a fine spray for combustion, and it wears from constant fuel flow at pressure, gradually changing the spray pattern away from the burner manufacturer's specification even before it visibly fails. A worn nozzle burns less cleanly, producing more soot that coats the heat exchanger's baffles, and a sooted heat exchanger loses efficiency in the same way scale does on a gas boiler's plates. Standard practice on an annual oil service is to replace the nozzle as a matter of course, rather than wait for a fault, and to remove and clean the baffles so the heat exchanger surfaces are exposed to combustion heat properly again. Skipping nozzle replacement to save a service visit's minor parts cost is a false economy against the fuel wasted by a poorly atomising burner.

Working across Somerset: what being local changes

Being based at 24 Bristol Road, Radstock, 10 miles from Swainswick via the A46, means a callout doesn't involve a long cross-county drive, and it also means familiarity with the recurring patterns in the local building stock — rural farmsteads and cottages — rather than encountering that construction type for the first time on-site. Local knowledge doesn't replace a proper site survey, but it does mean fewer surprises: knowing in advance that a particular postcode area typically has hard water, older single-pipe circuits, or restricted parking means the quote reflects the likely reality of the job before the first visit. We're Gas Safe and OFTEC registered and work across Somerset on that basis, not by claiming coverage we don't actually deliver on.

LPG as an alternative to oil off the gas grid

Properties around Swainswick that sit off the mains gas network aren't limited to oil — bulk LPG, stored in an above-ground tank on a concrete base with the same OFTEC-style clearance and access rules as oil, runs standard gas-rated boilers with only a change of injector and pressure setting rather than a different boiler entirely. It suits households that want a gas hob and gas-style modulation rather than an oil burner's on/off firing pattern. The tank still needs delivery access for a tanker, which on some rural driveways is the deciding factor over oil. We check the access route for the largest realistic delivery vehicle before recommending LPG over oil, because a tank that can't be filled easily causes more disruption than the fuel choice was meant to solve.

Other boiler services in Swainswick

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote