Who actually carries out the work?

A Gas Safe and, where relevant, OFTEC registered engineer from our own small team carries out the job — we don't sub the install out to a third party after quoting. You deal with the same people from survey through to commissioning and any aftercare calls.

Do we need planning permission for a new boiler flue on a listed or conservation-area property?

If the property is listed, Listed Building Consent can be needed for anything altering its appearance, including a new external flue terminal, even where the work itself would normally be permitted development. In conservation areas like parts of Wellow's setting, flue position and visibility from the street can also come under scrutiny. We flag this at survey rather than after ordering the boiler.

Can you look over a quote I've already had from another company?

Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.

We've got an oil-fired Rayburn or Aga heating the house — can that be replaced with a standard boiler?

Yes, where a range cooker like a Rayburn or Aga is also running the central heating, it can be separated out and replaced with a dedicated modern oil or LPG boiler, keeping the range purely for cooking if you want to retain it, or removing it entirely. Sizing the new boiler correctly for the property is the key part of getting this right.

We've still got an old back boiler behind the fireplace — what's involved in removing it?

Removing a back boiler means capping off the gas and water connections behind the fireplace, making good the opening or fitting a new fire/surround if you're keeping one, and rerouting pipework to the new combi or system boiler's position. It's more work than a like-for-like swap but a common upgrade on the older housing stock in this area.

Why do quotes vary so much in BA2?

Because the install matters more than the boiler. Two Wellow homes can have very different gas pipe sizes, flue routes and condensate runs — that's where the cost really moves.

Boiler Service Cost

Boiler Service Cost, How Much Is a New Boiler in Wellow?

Some properties make boiler service cost straightforward; others need a bit more thought about parking, access to the boiler cupboard, or how equipment gets in and out. We factor that into the visit rather than discovering it on the day. Working from 24 Bristol Road, Radstock BA3 3EE across the Radstock, Bath and Mendip area, we're Gas Safe registered and OFTEC registered, so both mains gas and oil-fired work is covered under one roof. homes alongside small commercial and agricultural premises make up most enquiries from this postcode. Most of what we open up here is stone village cottages and farmhouses, which dictates flue routes and pipe sizing. In Wellow itself (BA2, Somerset) that usually means stone village cottages and farmhouses, roughly 3 miles from the workshop.

07516 118198 See our hours

BA2 · Somerset · 3 mi from Radstock · unclassified

Gas-fired appliance serving a level property near Wellow, boiler service cost in Wellow (BA2) — unclassified corridor

Being close to our Radstock base means straightforward logistics for a job here — quick access for the survey, easy return visits if anything needs revisiting, and no long travel factored into how the work is scheduled. That doesn't change the standard of the work itself, but it does tend to make arranging visits and follow-ups a bit more flexible than for properties further out toward the edge of the area we cover. Nearest neighbours on our round are Peasedown St John, Combe Hay, Hinton Charterhouse. Terrain is level, which matters for condensate runs and tank siting. What changes a new boiler price in Wellow more than the brand is the building itself: stone village cottages and farmhouses drive different flue routes, gas-pipe sizing and controls choices. That's why we visit before fixing a price.

What backs up a Wellow quote

Fixed written prices

No verbal-only quotes — every figure is in writing with the boiler, controls and warranty spelled out.

No commission selling

Our engineers aren't paid on what you buy — there's no incentive to upsell you to a bigger boiler.

Checkatrade 9.9/10

362+ verified reviews from real customers across BA and BS postcodes.

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

Where else we work near Wellow

We cover Wellow alongside Peasedown St John (BA2), Combe Hay (BA2), Hinton Charterhouse (BA2), Shoscombe (BA2) — so spares, follow-ups and annual visits are easy to schedule together.

What's included in our price — Wellow

Boiler, flue and standard controls
Magnetic filter + chemical inhibitor
System flush appropriate to system age
All gas / oil works, building notification
Commissioning, handover and paperwork
Warranty registration with the manufacturer

Why Wellow work is specified differently

Common queries, answered honestly

Who actually carries out the work?: A Gas Safe and, where relevant, OFTEC registered engineer from our own small team carries out the job — we don't sub the install out to a third party after quoting. You deal with the same people from survey through to commissioning and any aftercare calls.
Do we need planning permission for a new boiler flue on a listed or conservation-area property?: If the property is listed, Listed Building Consent can be needed for anything altering its appearance, including a new external flue terminal, even where the work itself would normally be permitted development. In conservation areas like parts of Wellow's setting, flue position and visibility from the street can also come under scrutiny. We flag this at survey rather than after ordering the boiler.
Can you look over a quote I've already had from another company?: Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.
We've got an oil-fired Rayburn or Aga heating the house — can that be replaced with a standard boiler?: Yes, where a range cooker like a Rayburn or Aga is also running the central heating, it can be separated out and replaced with a dedicated modern oil or LPG boiler, keeping the range purely for cooking if you want to retain it, or removing it entirely. Sizing the new boiler correctly for the property is the key part of getting this right.
We've still got an old back boiler behind the fireplace — what's involved in removing it?: Removing a back boiler means capping off the gas and water connections behind the fireplace, making good the opening or fitting a new fire/surround if you're keeping one, and rerouting pipework to the new combi or system boiler's position. It's more work than a like-for-like swap but a common upgrade on the older housing stock in this area.
Why do quotes vary so much in BA2?: Because the install matters more than the boiler. Two Wellow homes can have very different gas pipe sizes, flue routes and condensate runs — that's where the cost really moves.

Coverage detail for BA2

County: Somerset
Postcode district: BA2
Settlement type: village
Nearest classified road: unclassified
Distance from our base: 3 miles (Radstock, BA3)
Typical building stock: stone village cottages and farmhouses
Water hardness: very hard limestone water
Fuel availability: mains gas with off-grid pockets
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Peasedown St John, Combe Hay, Hinton Charterhouse, Shoscombe

Practical considerations across BA2

Single-pipe circuits in older stone cottages

A lot of the stone cottages and farmhouses around Wellow were plumbed decades ago on a single-pipe gravity circuit, where each radiator draws from and returns to the same loop rather than having its own flow and return. It works, but radiators furthest from the boiler receive water that's already cooled after giving up heat to the ones before it, so the far end of the house is always the coldest. Converting to a two-pipe layout means new pipe runs, which in a stone cottage often means chasing lime plaster or lifting flagstones — not a trivial job. Where a full rewire of the pipework isn't wanted, we sometimes improve balance instead by oversizing the radiators nearest the end of the run and fitting TRVs to hold back the ones nearest the boiler.

Oil tank de-sludging: why it's not optional

Oil sitting in a tank for years accumulates water from condensation and fine sediment that settles at the bottom, and over time this forms a sludge layer that can be drawn into the fuel line, particularly when the tank is nearly empty and the outlet pulls from lower in the tank than usual. Sludge blocks fine oil filters and burner nozzles, which shows up as burner lockouts or a boiler that won't fire cleanly rather than as an obvious tank problem. De-sludging drains and cleans the tank base without necessarily removing the whole tank, and it's worth doing when a tank is inherited with a property, before switching to a new boiler, or if lockouts recur despite the filter and nozzle being replaced. It's a preventative job that's cheaper done on schedule than after a burner failure it caused.

Radiator sizing after lowering the flow temperature

Running a boiler at a lower flow temperature — typically 55°C or below rather than the old default of 70-80°C — improves condensing efficiency measurably, but it also reduces the heat output of every radiator in the house, because a radiator's output falls roughly with the square of the temperature difference to the room. Radiators sized correctly for a 75°C flow can end up unable to heat the room properly at 55°C unless they're upsized or supplemented. We check each radiator against the lower design flow temperature before recommending it, and where a room falls short we look at whether a larger single panel, a double panel, or an additional radiator on that circuit closes the gap, rather than pushing the flow temperature back up and giving away the efficiency gain.

Pumped-oil versus gravity feed: does it matter?

Older oil systems sometimes still rely on gravity feed, where the tank sits higher than the burner and oil flows down to it under its own weight; a pumped system uses the burner's internal pump to draw oil up from a tank at any level, including below the boiler. Gravity feed limits where a tank can be sited and is more prone to airlocks if the line runs dry, while a pumped system is more flexible on tank position but needs the pipe run and lift height kept within the burner pump's rated capacity — usually no more than a few metres of lift and a set maximum run length. When we replace an oil boiler we check which type the existing tank and pipework support before assuming a straight swap, because a tank sited for gravity feed may need repositioning or a different pump to suit a modern burner.

How a condensing boiler recovers extra heat

A condensing boiler passes flue gases through a secondary heat exchanger before they leave the flue, extracting additional heat by condensing water vapour in the exhaust back into liquid, which is expelled as the mildly acidic condensate water down the drain. This is why every condensing boiler needs a condensate drainage route as part of its installation, unlike older non-condensing boilers, which simply vented hot dry gas straight out. The efficiency benefit only fully materialises when the boiler is actually condensing regularly, which needs a return water temperature low enough — generally below 55°C — for water vapour to condense in the first place. A condensing boiler run permanently at a high flow temperature can spend much of its time not actually condensing, which is one of the main reasons flow temperature settings matter as much as the boiler model chosen.

Being minutes away in Wellow

Wellow sits close enough to our Radstock base, just 3 miles via the unclassified, that a diagnostic visit or a return trip for a part doesn't add the delay it would on a job further afield. That's practically useful on jobs where a fault only shows itself once a boiler's been running for a while, or where a part needs collecting after an initial diagnosis rather than being carried on the off-chance. It doesn't change how the job itself is done — the same Gas Safe and OFTEC standards and the same commissioning paperwork apply regardless of distance — but it does mean less waiting between visits on multi-stage jobs like a full system upgrade that needs a survey, a flush, and an installation visit in sequence.

Reaching properties off the main road network

Wellow is reached via the unclassified, an unclassified road rather than a numbered route, which matters mainly for winter access and for confirming a delivery vehicle carrying a new oil tank or bulky equipment can realistically reach the property. We factor the actual route in when scheduling deliveries or larger installations, checking with the customer about any width, height or surface restrictions on the final approach rather than assuming a mapping app's route reflects what a loaded van can manage. It rarely changes the technical scope of a job, but it does affect how a visit is planned and timed, particularly for jobs needing a specific delivery slot to coincide with the installation date.

Signs a boiler repair is no longer the right call

A boiler that's failing repeatedly, needing a different part replaced every service, or over roughly ten to fifteen years old is approaching the point where continued repair costs more over time than replacement, particularly once a heat exchanger — the most expensive single part — starts to show signs of failure through leaks or reduced output. Efficiency is the other half of the calculation: an older non-condensing boiler running at 70-80% efficiency against a modern condensing combi at over 90% means a meaningful chunk of every unit of fuel burned in the old boiler is simply lost up the flue. We give a straight answer on repair versus replace based on the fault found and the boiler's age and condition, rather than defaulting to whichever is more profitable to us on the day.

Your next move in BA2

Once boiler service cost is complete, you'll have the documentation that goes with it — commissioning records and, where applicable, Gas Safe or OFTEC paperwork and manufacturer registration for the guarantee. Keep it somewhere safe; it's what an agent, buyer or insurer will ask to see later. Call 07516 118198 and we will confirm a visit slot for BA2. Nearest neighbours on our round are Peasedown St John, Combe Hay, Hinton Charterhouse. homes alongside small commercial and agricultural premises make up most enquiries from this postcode.

07516 118198 All services in Wellow

Related help for Wellow

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote