Is oil more expensive to run than mains gas?

Oil and gas prices both move with the wholesale market and neither is fixed, so a blanket answer isn't honest. What we can say is that a modern condensing oil boiler, correctly sized and commissioned, will run considerably more efficiently than an old non-condensing model — that efficiency gap usually matters more than the fuel choice itself.

What's actually checked during an annual boiler service?

A service includes a visual and functional check of the boiler's casing and controls, flue gas analysis to confirm safe and efficient combustion, checking the flame picture and pressure, inspecting seals and condensate, and testing safety devices. It's a safety check as much as a performance one, and it's what keeps most manufacturer warranties valid.

Who actually carries out the work?

A Gas Safe and, where relevant, OFTEC registered engineer from our own small team carries out the job — we don't sub the install out to a third party after quoting. You deal with the same people from survey through to commissioning and any aftercare calls.

What actually happens on install day?

The engineer isolates the gas or oil supply and water, removes the old boiler, fits and pressure-tests the new one, connects the flue and condensate, and commissions the system. For a straight swap this is usually one day; a conversion, relocation, or cylinder change can run into a second depending on the pipework involved.

What's the difference between a power flush and a chemical flush?

A chemical flush circulates a cleaning agent through the existing system to loosen light debris, while a power flush uses a pump to force water at higher velocity and reversed direction through radiators and pipework to shift heavier sludge. We usually recommend the more thorough power flush before connecting a new boiler to an older system.

What's the warranty on a new boiler installed in Odd Down?

Up to 10 years on qualifying Worcester Bosch installs registered through us as Accredited Installers. Other manufacturers typically offer 5–7 years.

Odd Down's Local Boiler Installation Specialist

Boiler Installation covers a range of jobs, from straightforward like-for-like swaps to full system redesigns with new pipework, controls and hot water storage. The right approach depends on boiler location, flue length, pump speed, radiator sizing and how the property loses heat. As a Gas Safe and OFTEC registered firm and a Worcester Bosch Accredited Installer working out of Radstock, we specify each install against the building rather than fitting a standard package regardless of fit. Most of what we open up here is 1950s–70s estate housing, which dictates flue routes and pipe sizing. Nearest neighbours on our round are Combe Down, Bear Flat, South Stoke. In Odd Down itself (BA2, Somerset) that usually means 1950s–70s estate housing, roughly 8 miles from the workshop.

07516 118198 See our hours

BA2 · Somerset · 8 mi from Radstock · A367

Boiler Installation on a suburb property 8 miles from Radstock, boiler installation in Odd Down (BA2) — open suburban access

Reading the property before pricing the work

Water here runs off carboniferous limestone and Jurassic oolite, which makes it very hard by national standards. Hard water accelerates scale build-up inside heat exchangers, cylinders and pipework, which shortens the working life of components that aren't protected against it. On jobs in this area we factor scale protection into the specification rather than treating it as an optional extra, because the difference between a protected and unprotected system shows up within a few years, not decades. It's a genuine local variable, not generic sales advice, and it applies whether the property is on mains gas or oil. Water here is very hard limestone water, so scale protection is specified accordingly. Our van runs the A367 to reach you, 8 miles out from the Radstock workshop. Odd Down is roughly 8 miles from our Radstock base via the A367. Typical property stock here: 1950s–70s estate housing. Odd Down sits in the Somerset BA2 postcode and is part of our weekly run, so local response is quick. When we quote boiler installation here we factor in flue routing, condensate fall and gas-supply pipe sizing before the price is fixed.

Also covering the lanes around Odd Down

Beyond Odd Down we're frequently on jobs in Combe Down (BA2), Bear Flat (BA2), South Stoke (BA2) and Englishcombe (BA2) — so spares, follow-ups and annual services are straightforward.

Registrations and how work is signed off

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Fixed written prices

No verbal-only quotes. You'll get the boiler model, controls and warranty in writing before we book.

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

Included as standard in Odd Down

Combi, system & regular boilers
Like-for-like swaps in a single day
Worcester, Vaillant, Ideal, Grant & more
Up to 10-year manufacturer warranties
Free written quote, no obligation
Local aftercare from a 8-mile base

Questions before you book

Is oil more expensive to run than mains gas?: Oil and gas prices both move with the wholesale market and neither is fixed, so a blanket answer isn't honest. What we can say is that a modern condensing oil boiler, correctly sized and commissioned, will run considerably more efficiently than an old non-condensing model — that efficiency gap usually matters more than the fuel choice itself.
What's actually checked during an annual boiler service?: A service includes a visual and functional check of the boiler's casing and controls, flue gas analysis to confirm safe and efficient combustion, checking the flame picture and pressure, inspecting seals and condensate, and testing safety devices. It's a safety check as much as a performance one, and it's what keeps most manufacturer warranties valid.
Who actually carries out the work?: A Gas Safe and, where relevant, OFTEC registered engineer from our own small team carries out the job — we don't sub the install out to a third party after quoting. You deal with the same people from survey through to commissioning and any aftercare calls.
What actually happens on install day?: The engineer isolates the gas or oil supply and water, removes the old boiler, fits and pressure-tests the new one, connects the flue and condensate, and commissions the system. For a straight swap this is usually one day; a conversion, relocation, or cylinder change can run into a second depending on the pipework involved.
What's the difference between a power flush and a chemical flush?: A chemical flush circulates a cleaning agent through the existing system to loosen light debris, while a power flush uses a pump to force water at higher velocity and reversed direction through radiators and pipework to shift heavier sludge. We usually recommend the more thorough power flush before connecting a new boiler to an older system.
What's the warranty on a new boiler installed in Odd Down?: Up to 10 years on qualifying Worcester Bosch installs registered through us as Accredited Installers. Other manufacturers typically offer 5–7 years.

Your next move in BA2

Once we've seen the property, you'll get a written quote for boiler installation that sets out exactly what's included — the equipment, the work, and what happens if anything unexpected turns up once we're on site. That gives you something concrete to compare against any other quotes you're getting. A written quote follows the survey — no pressure, and no charge for the Odd Down visit. Typical era of build is postwar, which affects existing pipework and system cleanliness. a high proportion of rented and let properties make up most enquiries from this postcode.

07516 118198 All services in Odd Down

Odd Down coverage and distances

County: Somerset
Postcode district: BA2
Settlement type: suburb
Nearest classified road: A367
Distance from our base: 8 miles (Radstock, BA3)
Typical building stock: 1950s–70s estate housing
Water hardness: very hard limestone water
Fuel availability: mains gas with off-grid pockets
Customer mix: a high proportion of rented and let properties
Nearby areas covered: Combe Down, Bear Flat, South Stoke, Englishcombe

Things we check around Odd Down

Radiator sizing after lowering the flow temperature

Running a boiler at a lower flow temperature — typically 55°C or below rather than the old default of 70-80°C — improves condensing efficiency measurably, but it also reduces the heat output of every radiator in the house, because a radiator's output falls roughly with the square of the temperature difference to the room. Radiators sized correctly for a 75°C flow can end up unable to heat the room properly at 55°C unless they're upsized or supplemented. We check each radiator against the lower design flow temperature before recommending it, and where a room falls short we look at whether a larger single panel, a double panel, or an additional radiator on that circuit closes the gap, rather than pushing the flow temperature back up and giving away the efficiency gain.

How a condensing boiler recovers extra heat

A condensing boiler passes flue gases through a secondary heat exchanger before they leave the flue, extracting additional heat by condensing water vapour in the exhaust back into liquid, which is expelled as the mildly acidic condensate water down the drain. This is why every condensing boiler needs a condensate drainage route as part of its installation, unlike older non-condensing boilers, which simply vented hot dry gas straight out. The efficiency benefit only fully materialises when the boiler is actually condensing regularly, which needs a return water temperature low enough — generally below 55°C — for water vapour to condense in the first place. A condensing boiler run permanently at a high flow temperature can spend much of its time not actually condensing, which is one of the main reasons flow temperature settings matter as much as the boiler model chosen.

Heating in 1950s-60s built housing

Housing built through the 1950s and 60s around Odd Down, including ex-local-authority stock, often has solid or early cavity wall construction with limited or no cavity insulation, giving a heat loss profile between older solid-wall Victorian stock and modern insulated builds. Original heating pipework from this era is a mix — some properties were plumbed with early microbore retrofits, others kept full-bore two-pipe systems throughout — so assuming a standard layout without checking is unreliable. Loft insulation levels also vary significantly between individual properties even on the same estate, depending on what's been added since construction, which affects the heat loss calculation more than the build era label alone would suggest. We check actual insulation and pipework on site rather than assuming a standard 1960s answer.

Pumped-oil versus gravity feed: does it matter?

Older oil systems sometimes still rely on gravity feed, where the tank sits higher than the burner and oil flows down to it under its own weight; a pumped system uses the burner's internal pump to draw oil up from a tank at any level, including below the boiler. Gravity feed limits where a tank can be sited and is more prone to airlocks if the line runs dry, while a pumped system is more flexible on tank position but needs the pipe run and lift height kept within the burner pump's rated capacity — usually no more than a few metres of lift and a set maximum run length. When we replace an oil boiler we check which type the existing tank and pipework support before assuming a straight swap, because a tank sited for gravity feed may need repositioning or a different pump to suit a modern burner.

Why very hard limestone water shortens boiler life around Odd Down

The limestone geology under Somerset gives Odd Down very hard limestone water, which drops calcium carbonate out of solution as soon as it's heated. Inside a combi's plate heat exchanger the gaps between plates are only a millimetre or two wide, so scale narrows the waterways long before it's visible anywhere else in the system. The first symptom is usually a hot tap that runs warm rather than hot, or a boiler that fires more often for the same demand. Left unchecked, scale insulates the exchanger from the burner, forces flue gases hotter, and can crack the exchanger from thermal stress. A scale reducer fitted on the mains feed, sized to the property's flow rate, is cheaper to install once than to replace a heat exchanger twice.

Common boiler fault codes and what usually causes them

Most modern boilers display a fault code on the control panel when they lock out, and while the exact code differs between manufacturers, the underlying causes cluster into a small number of categories: low system pressure (often from a small leak or after bleeding radiators), ignition failure (a worn electrode, gas supply issue, or blocked condensate causing a safety shutdown), or a failed sensor reporting an implausible temperature reading. A condensate blockage or freeze specifically tends to show a distinct code from a genuine ignition fault, which is why checking the external condensate pipe for ice before calling out an engineer in a cold snap can sometimes resolve the issue without a visit at all. We ask for the exact fault code and any recent history — a bled radiator, a cold snap, a recent service — before attending, since it often narrows down the likely cause before we arrive.

Other boiler services in Odd Down

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote