Who actually carries out the work?

A Gas Safe and, where relevant, OFTEC registered engineer from our own small team carries out the job — we don't sub the install out to a third party after quoting. You deal with the same people from survey through to commissioning and any aftercare calls.

Is a boiler install a noisy, disruptive job?

There's unavoidable noise — drilling for the flue, pipework, sometimes moving a cylinder — but a straightforward swap is usually done within a working day with the mess kept to the immediate work area. We dust-sheet the route in and out and clear away pipe offcuts and old parts before we leave.

What actually happens on install day?

The engineer isolates the gas or oil supply and water, removes the old boiler, fits and pressure-tests the new one, connects the flue and condensate, and commissions the system. For a straight swap this is usually one day; a conversion, relocation, or cylinder change can run into a second depending on the pipework involved.

What's the difference between a power flush and a chemical flush?

A chemical flush circulates a cleaning agent through the existing system to loosen light debris, while a power flush uses a pump to force water at higher velocity and reversed direction through radiators and pipework to shift heavier sludge. We usually recommend the more thorough power flush before connecting a new boiler to an older system.

Can you look over a quote I've already had from another company?

Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.

As a landlord, how quickly can you deal with a no-heat call for a tenant?

We book calls in during our published hours, Monday to Friday 8:30 to 5, and don't operate an out-of-hours emergency line, so we're upfront that a weekend no-heat call will wait until the next working day unless you've other cover in place. During the week we prioritise no-heat and no-hot-water calls where we can.

Boiler Installation in Bath

Not every property near us sits on the mains gas network, and boiler installation for an off-grid home means thinking about oil, tank location and delivery access alongside the heating system itself. We're OFTEC registered as well as Gas Safe registered, so oil-fired work gets the same attention as mains gas from our base at 24 Bristol Road, Radstock BA3 3EE, rather than being treated as an afterthought. Water here is very hard limestone water, so scale protection is specified accordingly. a high proportion of rented and let properties make up most enquiries from this postcode. In Bath itself (BA1, Somerset) that usually means georgian townhouses, victorian terraces, modern flats, roughly 8 miles from the workshop.

07516 118198 Book a survey

BA1 · Somerset · 8 mi from Radstock · A36

Gas-fired appliance serving a level property near Bath, boiler installation in Bath (BA1) — A36 corridor

Scope of work, itemised

Combi, system & regular boilers
Like-for-like swaps in a single day
Worcester, Vaillant, Ideal, Grant & more
Up to 10-year manufacturer warranties
Free written quote, no obligation
Local aftercare from a 8-mile base

Registrations and how work is signed off

Fixed written prices

No verbal-only quotes. You'll get the boiler model, controls and warranty in writing before we book.

Checkatrade 9.9/10

362+ verified reviews from real customers across BA and BS postcodes.

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

Neighbouring Somerset areas we serve

Beyond Bath we're frequently on jobs in Lansdown (BA1), Larkhall (BA1), Combe Down (BA2) and Bathampton (BA2) — so spares, follow-ups and annual services are straightforward.

Why Bath work is specified differently

Water here runs off carboniferous limestone and Jurassic oolite, which makes it very hard by national standards. Hard water accelerates scale build-up inside heat exchangers, cylinders and pipework, which shortens the working life of components that aren't protected against it. On jobs in this area we factor scale protection into the specification rather than treating it as an optional extra, because the difference between a protected and unprotected system shows up within a few years, not decades. It's a genuine local variable, not generic sales advice, and it applies whether the property is on mains gas or oil. Mains gas is available across most streets, which changes the appliance shortlist. Most of what we open up here is georgian townhouses, victorian terraces, modern flats, which dictates flue routes and pipe sizing. Bath is roughly 8 miles from our Radstock base via the A36. Typical property stock here: Georgian townhouses, Victorian terraces, modern flats. Mains gas covers most of Bath, so the usual choice is between a modern combi or a system boiler with a cylinder — we'll size it correctly for the home, not just swap like-for-like. When we quote boiler installation here we factor in flue routing, condensate fall and gas-supply pipe sizing before the price is fixed.

Straight answers for Bath homeowners

Who actually carries out the work?: A Gas Safe and, where relevant, OFTEC registered engineer from our own small team carries out the job — we don't sub the install out to a third party after quoting. You deal with the same people from survey through to commissioning and any aftercare calls.
Is a boiler install a noisy, disruptive job?: There's unavoidable noise — drilling for the flue, pipework, sometimes moving a cylinder — but a straightforward swap is usually done within a working day with the mess kept to the immediate work area. We dust-sheet the route in and out and clear away pipe offcuts and old parts before we leave.
What actually happens on install day?: The engineer isolates the gas or oil supply and water, removes the old boiler, fits and pressure-tests the new one, connects the flue and condensate, and commissions the system. For a straight swap this is usually one day; a conversion, relocation, or cylinder change can run into a second depending on the pipework involved.
What's the difference between a power flush and a chemical flush?: A chemical flush circulates a cleaning agent through the existing system to loosen light debris, while a power flush uses a pump to force water at higher velocity and reversed direction through radiators and pipework to shift heavier sludge. We usually recommend the more thorough power flush before connecting a new boiler to an older system.
Can you look over a quote I've already had from another company?: Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.
As a landlord, how quickly can you deal with a no-heat call for a tenant?: We book calls in during our published hours, Monday to Friday 8:30 to 5, and don't operate an out-of-hours emergency line, so we're upfront that a weekend no-heat call will wait until the next working day unless you've other cover in place. During the week we prioritise no-heat and no-hot-water calls where we can.

Next step for Bath

For landlords, boiler installation usually needs to fit around a tenancy, so let us know at the outset if the property is occupied and what access arrangements work for the tenant. We'll build that into the quote and the schedule rather than assuming an empty property. Call 07516 118198 and we will confirm a visit slot for BA1. Terrain is level, which matters for condensate runs and tank siting. Our van runs the A36 to reach you, 8 miles out from the Radstock workshop.

07516 118198 All services in Bath

Bath at a glance

County: Somerset
Postcode district: BA1
Settlement type: city
Nearest classified road: A36
Distance from our base: 8 miles (Radstock, BA3)
Typical building stock: Georgian townhouses, Victorian terraces, modern flats
Water hardness: very hard limestone water
Fuel availability: mains gas across most of the area
Customer mix: a high proportion of rented and let properties
Nearby areas covered: Lansdown, Larkhall, Combe Down, Bathampton

The parts of the job people rarely mention

Oil tank de-sludging: why it's not optional

Oil sitting in a tank for years accumulates water from condensation and fine sediment that settles at the bottom, and over time this forms a sludge layer that can be drawn into the fuel line, particularly when the tank is nearly empty and the outlet pulls from lower in the tank than usual. Sludge blocks fine oil filters and burner nozzles, which shows up as burner lockouts or a boiler that won't fire cleanly rather than as an obvious tank problem. De-sludging drains and cleans the tank base without necessarily removing the whole tank, and it's worth doing when a tank is inherited with a property, before switching to a new boiler, or if lockouts recur despite the filter and nozzle being replaced. It's a preventative job that's cheaper done on schedule than after a burner failure it caused.

What different boiler noises usually mean

A kettling or rumbling sound from a boiler is most often scale or sludge build-up on the heat exchanger causing localised boiling as water is trapped and overheated in restricted channels — the heating equivalent of a kettle furring up. A banging or knocking sound in pipework, sometimes called water hammer, is usually caused by a valve closing too quickly or trapped air rather than the boiler itself. A whining or humming sound tends to point to the circulating pump, either from wear or from air in the system reducing lubrication at the bearing. Diagnosing correctly from the noise alone isn't reliable enough to act on without checking system pressure, inhibitor condition and the pump directly, but the noise itself is a useful first indicator of which of those to check first.

Electronic and physical scale reducers compared

In very hard limestone water areas like Bath, a scale reducer fitted on the boiler's cold feed protects the heat exchanger without the ongoing salt and drainage requirements of a full water softener. Physical scale reducers use a polyphosphate or template-assisted crystallisation cartridge that alters how calcium carbonate crystallises so it's less likely to adhere to hot surfaces; electronic and electromagnetic devices claim a similar effect without a cartridge to replace, though the evidence base for electronic types is weaker and more inconsistent than for physical media. Manufacturers including Worcester Bosch now specify a scale reducer or softener as a condition of extended guarantees in hard water areas, so the choice affects warranty validity as well as long-term performance, not just descale frequency.

Chimney liners for boilers using an existing flue

Where an older boiler used the property's original brick or stone chimney as its flue route, a replacement condensing boiler usually can't use the same masonry flue unlined, because the flue gases are cooler and wetter and will attack unprotected brickwork and mortar over time. A correctly specified stainless steel liner, sized to the boiler manufacturer's flue length and diameter tables, carries the flue gases safely and lets the existing chimney be reused rather than needing a new wall or roof penetration — often the only realistic option on a listed or solid-wall property in Bath where an external flue run isn't permitted. The liner has to be inspected and swept as part of ongoing servicing exactly as an open-fire flue would be, which is easy to overlook once it's hidden inside the chimney.

Chasing pipework into lime plaster and stone walls

Solid stone or cob walls finished in lime plaster, common in the older parts of Bath, behave very differently to modern plasterboard when a pipe run needs chasing in. Lime plaster is softer and more porous than gypsum, so cutting a neat, consistent chase without blowing the surface needs a slower hand and finer disc than a stud-wall job, and any repair has to be made good in a lime-based skim rather than modern filler, which can trap moisture behind it and cause the patch to fail. On solid stone we sometimes surface-mount pipework in painted conduit instead of chasing, particularly where the wall is a significant structural thickness and chasing would weaken it. Knowing which approach a wall needs before starting avoids expensive plaster damage.

What OpenTherm controls actually change

A standard on/off thermostat tells the boiler to fire at full output until the room reaches temperature, then switches it off completely — a crude control strategy that causes temperature overshoot and more burner cycling than necessary. An OpenTherm-compatible thermostat instead communicates continuously with a compatible boiler, asking for a modulated flow temperature based on how far the room is from target, so the boiler runs at a lower, steadier output for longer rather than firing at full power in short bursts. The efficiency gain depends on the boiler actually supporting OpenTherm modulation, which not every combi does even where the wiring terminals are compatible. We check the boiler's own specification against the thermostat's control protocol before recommending an upgrade, since fitting an OpenTherm stat on a boiler that ignores the modulation signal wastes the thermostat's main feature.

Why very hard limestone water shortens boiler life around Bath

The limestone geology under Somerset gives Bath very hard limestone water, which drops calcium carbonate out of solution as soon as it's heated. Inside a combi's plate heat exchanger the gaps between plates are only a millimetre or two wide, so scale narrows the waterways long before it's visible anywhere else in the system. The first symptom is usually a hot tap that runs warm rather than hot, or a boiler that fires more often for the same demand. Left unchecked, scale insulates the exchanger from the burner, forces flue gases hotter, and can crack the exchanger from thermal stress. A scale reducer fitted on the mains feed, sized to the property's flow rate, is cheaper to install once than to replace a heat exchanger twice.

Other boiler services in Bath

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote