We've got an oil-fired Rayburn or Aga heating the house — can that be replaced with a standard boiler?

Yes, where a range cooker like a Rayburn or Aga is also running the central heating, it can be separated out and replaced with a dedicated modern oil or LPG boiler, keeping the range purely for cooking if you want to retain it, or removing it entirely. Sizing the new boiler correctly for the property is the key part of getting this right.

What support do I get after the install is finished?

Once commissioning's complete we talk you through the controls, leave the paperwork, and register the manufacturer warranty on your behalf. If anything doesn't feel right in the first few weeks — a fault code, an odd noise, a control setting you're unsure of — call us during office hours and we'll talk it through or come back out.

How does LPG heating differ from mains gas day to day?

An LPG boiler works the same way as a mains gas one day to day, but the gas is stored in a tank or cylinders on site and topped up by a supplier rather than piped in continuously. That means keeping an eye on tank levels and arranging deliveries, but appliance choice, controls, and servicing requirements are otherwise very similar.

Is it worth upgrading the heating controls when we replace the boiler?

Where the existing controls are an old mechanical timer and single room thermostat, replacing them alongside the boiler with weather compensation or a modern programmable thermostat usually improves comfort and efficiency more than the boiler swap alone. It's not compulsory, but it's often the single best-value addition to a new install.

We run a holiday let — do the same gas safety rules apply as a standard rental?

Yes, holiday lets fall under the same landlord gas safety duty as any other let property — an annual CP12 from a Gas Safe registered engineer is required, and it's worth timing the visit for a gap between bookings rather than trying to fit it around guests, which we're happy to help plan around.

Will you come out to a village like Ditcheat?

Ditcheat is part of our core patch (9 miles from base via the unclassified). Same-week site visits and quick callbacks are normal.

Local Oil Tank Replacement for Ditcheat

When you're comparing tradespeople for oil tank replacement, it's worth checking registration before price: Gas Safe for mains gas work, OFTEC for oil, and manufacturer accreditation if a specific guarantee matters to you. We hold all three — Gas Safe, OFTEC and Worcester Bosch Accredited Installer status — and work from 24 Bristol Road, Radstock BA3 3EE, so you can check us against whatever criteria you're using to shortlist. Nearest neighbours on our round are Evercreech, Pylle, Shepton Mallet.

07516 118198 Call now

BA4 · Somerset · 9 mi from Radstock · unclassified

Oil Tank Replacement planned around lane access access in Ditcheat — 9 miles from our Radstock base

How Somerset building stock shapes the spec

Stone cottages and farmhouses around here were mostly built long before central heating existed, so pipework and boiler locations have usually been retrofitted at some point, sometimes more than once. Thick stone walls, uneven floor levels and low ceilings can all affect where a boiler or cylinder can practically go, and older stonework doesn't always take fixings the way modern block or brick does. We work around those constraints on site rather than assuming a straightforward install. Our van runs the unclassified to reach you, 9 miles out from the Radstock workshop. Ditcheat is roughly 9 miles from our Radstock base via the unclassified. Typical property stock here: stone farmhouses and cottages. A meaningful share of properties around Ditcheat are off the gas grid, so oil boiler installs and tank swaps make up a fair part of what we do locally. Repair calls in Ditcheat usually get a same-week visit, with most common faults fixed on the first attempt.

What backs up a Ditcheat quote

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Local, family-run

Based at 24 Bristol Rd, Radstock — every job is run by the team that quoted it.

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

Within reach of the unclassified

Beyond Ditcheat we're frequently on jobs in Evercreech (BA4), Pylle (BA4), Shepton Mallet (BA4) and Pilton (BA4) — so spares, follow-ups and annual services are straightforward.

How we run oil tank replacement on site

Bunded plastic and steel tanks supplied
Base preparation and safe siting distances
New supply line, filter and fire valve
Old tank drained and removed
Free written quote, no obligation
Local aftercare from a 9-mile base

Oil Tank Replacement FAQs for BA4

We've got an oil-fired Rayburn or Aga heating the house — can that be replaced with a standard boiler?: Yes, where a range cooker like a Rayburn or Aga is also running the central heating, it can be separated out and replaced with a dedicated modern oil or LPG boiler, keeping the range purely for cooking if you want to retain it, or removing it entirely. Sizing the new boiler correctly for the property is the key part of getting this right.
What support do I get after the install is finished?: Once commissioning's complete we talk you through the controls, leave the paperwork, and register the manufacturer warranty on your behalf. If anything doesn't feel right in the first few weeks — a fault code, an odd noise, a control setting you're unsure of — call us during office hours and we'll talk it through or come back out.
How does LPG heating differ from mains gas day to day?: An LPG boiler works the same way as a mains gas one day to day, but the gas is stored in a tank or cylinders on site and topped up by a supplier rather than piped in continuously. That means keeping an eye on tank levels and arranging deliveries, but appliance choice, controls, and servicing requirements are otherwise very similar.
Is it worth upgrading the heating controls when we replace the boiler?: Where the existing controls are an old mechanical timer and single room thermostat, replacing them alongside the boiler with weather compensation or a modern programmable thermostat usually improves comfort and efficiency more than the boiler swap alone. It's not compulsory, but it's often the single best-value addition to a new install.
We run a holiday let — do the same gas safety rules apply as a standard rental?: Yes, holiday lets fall under the same landlord gas safety duty as any other let property — an annual CP12 from a Gas Safe registered engineer is required, and it's worth timing the visit for a gap between bookings rather than trying to fit it around guests, which we're happy to help plan around.
Will you come out to a village like Ditcheat?: Ditcheat is part of our core patch (9 miles from base via the unclassified). Same-week site visits and quick callbacks are normal.

Booking work in Ditcheat

Once we've seen the property, you'll get a written quote for oil tank replacement that sets out exactly what's included — the equipment, the work, and what happens if anything unexpected turns up once we're on site. That gives you something concrete to compare against any other quotes you're getting. Send the appliance make, model and any fault code and you get a straight answer, not a sales script. Water here is moderately hard water, so scale protection is specified accordingly.

07516 118198 All services in Ditcheat

Ditcheat coverage and distances

County: Somerset
Postcode district: BA4
Settlement type: village
Nearest classified road: unclassified
Distance from our base: 9 miles (Radstock, BA3)
Typical building stock: stone farmhouses and cottages
Water hardness: moderately hard water
Fuel availability: mains gas with off-grid pockets
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Evercreech, Pylle, Shepton Mallet, Pilton

Detail that matters in Ditcheat

Pumped-oil versus gravity feed: does it matter?

Older oil systems sometimes still rely on gravity feed, where the tank sits higher than the burner and oil flows down to it under its own weight; a pumped system uses the burner's internal pump to draw oil up from a tank at any level, including below the boiler. Gravity feed limits where a tank can be sited and is more prone to airlocks if the line runs dry, while a pumped system is more flexible on tank position but needs the pipe run and lift height kept within the burner pump's rated capacity — usually no more than a few metres of lift and a set maximum run length. When we replace an oil boiler we check which type the existing tank and pipework support before assuming a straight swap, because a tank sited for gravity feed may need repositioning or a different pump to suit a modern burner.

Low-loss headers on larger or multi-zone systems

On a system with several heating zones or a boiler oversized relative to any single zone's flow requirement, a low-loss header hydraulically separates the boiler's primary circuit from the secondary zone circuits, so each side can run its own pump and flow rate without one interfering with the other. Without it, a zone valve closing on a multi-zone system can starve the boiler of flow or force excessive pump pressure through the remaining open zones. It's most relevant on larger properties or ones with commercial premises attached, where several distinct heating circuits — perhaps a shop unit and a flat above — share one heat source. Getting the header sized to the boiler's actual flow rate, not just fitted as standard, is what makes it work rather than just adding another connection.

LPG as an alternative to oil off the gas grid

Properties around Ditcheat that sit off the mains gas network aren't limited to oil — bulk LPG, stored in an above-ground tank on a concrete base with the same OFTEC-style clearance and access rules as oil, runs standard gas-rated boilers with only a change of injector and pressure setting rather than a different boiler entirely. It suits households that want a gas hob and gas-style modulation rather than an oil burner's on/off firing pattern. The tank still needs delivery access for a tanker, which on some rural driveways is the deciding factor over oil. We check the access route for the largest realistic delivery vehicle before recommending LPG over oil, because a tank that can't be filled easily causes more disruption than the fuel choice was meant to solve.

Nozzle replacement and baffle cleaning on oil burners

An oil burner's nozzle atomises fuel into a fine spray for combustion, and it wears from constant fuel flow at pressure, gradually changing the spray pattern away from the burner manufacturer's specification even before it visibly fails. A worn nozzle burns less cleanly, producing more soot that coats the heat exchanger's baffles, and a sooted heat exchanger loses efficiency in the same way scale does on a gas boiler's plates. Standard practice on an annual oil service is to replace the nozzle as a matter of course, rather than wait for a fault, and to remove and clean the baffles so the heat exchanger surfaces are exposed to combustion heat properly again. Skipping nozzle replacement to save a service visit's minor parts cost is a false economy against the fuel wasted by a poorly atomising burner.

Heating where a home sits alongside commercial premises

Properties around Ditcheat that combine living accommodation with an attached shop, workshop or other commercial space often need heating designed as genuinely separate zones with independent controls, since a shop's occupied hours and heating demand rarely match the flat or house above it. Where the two shared a single ageing system, splitting them onto separate zone valves — or, on a larger scale, separate boilers — stops one side subsidising or interfering with the other's heating schedule. Commercial space also sometimes falls under different servicing and safety-record obligations than the residential side, depending on how it's used, so it's worth establishing which parts of the building fall under which regime before assuming a single annual service covers everything.

Working across Somerset: what being local changes

Being based at 24 Bristol Road, Radstock, 9 miles from Ditcheat via the unclassified, means a callout doesn't involve a long cross-county drive, and it also means familiarity with the recurring patterns in the local building stock — stone farmhouses and cottages — rather than encountering that construction type for the first time on-site. Local knowledge doesn't replace a proper site survey, but it does mean fewer surprises: knowing in advance that a particular postcode area typically has hard water, older single-pipe circuits, or restricted parking means the quote reflects the likely reality of the job before the first visit. We're Gas Safe and OFTEC registered and work across Somerset on that basis, not by claiming coverage we don't actually deliver on.

What voids or protects a Worcester Bosch extended guarantee

Worcester Bosch's longer guarantee periods on qualifying installations are conditional on the boiler being installed and commissioned by an Accredited Installer, on an annual service being carried out (by any Gas Safe registered engineer, not necessarily the original installer) within the required window each year, and on system water quality being maintained to the standard set out in their published guidance — meaning a system flush at installation, correct inhibitor dosing, and in hard water areas a scale reducer or filter as specified. Missing a single annual service, or installing without the required water treatment, can reduce cover back to the manufacturer's standard guarantee period even if the boiler itself has had no faults. Keeping the Benchmark record and service history together is what lets a claim be assessed quickly if it's ever needed.

Chasing pipework into lime plaster and stone walls

Solid stone or cob walls finished in lime plaster, common in the older parts of Ditcheat, behave very differently to modern plasterboard when a pipe run needs chasing in. Lime plaster is softer and more porous than gypsum, so cutting a neat, consistent chase without blowing the surface needs a slower hand and finer disc than a stud-wall job, and any repair has to be made good in a lime-based skim rather than modern filler, which can trap moisture behind it and cause the patch to fail. On solid stone we sometimes surface-mount pipework in painted conduit instead of chasing, particularly where the wall is a significant structural thickness and chasing would weaken it. Knowing which approach a wall needs before starting avoids expensive plaster damage.

Other boiler services in Ditcheat

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote