As a landlord, how quickly can you deal with a no-heat call for a tenant?

We book calls in during our published hours, Monday to Friday 8:30 to 5, and don't operate an out-of-hours emergency line, so we're upfront that a weekend no-heat call will wait until the next working day unless you've other cover in place. During the week we prioritise no-heat and no-hot-water calls where we can.

What is condensate and why does its routing matter?

Condensate is the mildly acidic water produced by a modern condensing boiler as it extracts extra heat from the flue gases, and it needs a route to an internal drain or, less ideally, an external soakaway. In colder or more exposed locations an external condensate pipe can freeze and shut the boiler down, so internal routing is worth prioritising where the layout allows it.

Is a boiler install a noisy, disruptive job?

There's unavoidable noise — drilling for the flue, pipework, sometimes moving a cylinder — but a straightforward swap is usually done within a working day with the mess kept to the immediate work area. We dust-sheet the route in and out and clear away pipe offcuts and old parts before we leave.

Is it worth upgrading the heating controls when we replace the boiler?

Where the existing controls are an old mechanical timer and single room thermostat, replacing them alongside the boiler with weather compensation or a modern programmable thermostat usually improves comfort and efficiency more than the boiler swap alone. It's not compulsory, but it's often the single best-value addition to a new install.

How do you decide whether to repair or replace a boiler?

We weigh the age of the boiler, whether parts are still made for it, how many faults it's had recently, and its running efficiency against a like-for-like or upgraded replacement. If a straightforward part fixes it and the boiler's otherwise sound, we'll say so rather than push a new install you don't need.

Do you cover all of Melksham?

Yes — every street in SN12 that falls under Melksham, plus the lanes towards Holt and Staverton. We're 12 miles away in Radstock, so most jobs are reached in well under half an hour.

Melksham Gas Boiler Installation

Gas Boiler Installation sits alongside the wider servicing cycle a heating system goes through over its life: commissioning, annual checks, and eventually replacement once repairs stop making sense. Thinking about where you are in that cycle helps decide whether now is the right time to act. We're Gas Safe registered and OFTEC registered, based at 24 Bristol Road, Radstock BA3 3EE, and happy to talk through where your system currently sits before recommending anything. Most of what we open up here is victorian terraces and modern estates, which dictates flue routes and pipe sizing. Access is open suburban, so parking, spoil removal and delivery timing get planned in advance. In Melksham itself (SN12, Wiltshire) that usually means victorian terraces and modern estates, roughly 12 miles from the workshop.

07516 118198 Book a survey

SN12 · Wiltshire · 12 mi from Radstock · A350

Flue and pipework detail from a gas boiler installation job in Wiltshire, gas boiler installation in Melksham (SN12) — A350 corridor

Why Melksham work is specified differently

This settlement has a genuine mix of owner-occupied and rented housing, which means the priorities on any given job vary: an owner-occupier might prioritise long-term running costs, while a landlord is usually focused on reliability and having the right paperwork in place for tenants and agents. We ask early on which category a job falls into, since it shapes what matters most in the specification and what documentation needs to be provided at the end. Nearest neighbours on our round are Holt, Staverton, Trowbridge. Terrain is hill top, which matters for condensate runs and tank siting. Melksham is roughly 12 miles from our Radstock base via the A350. Typical property stock here: Victorian terraces and modern estates. Mains gas covers most of Melksham, so the usual choice is between a modern combi or a system boiler with a cylinder — we'll size it correctly for the home, not just swap like-for-like. When we quote gas boiler installation here we factor in flue routing, condensate fall and gas-supply pipe sizing before the price is fixed.

Nearby villages and neighbourhoods

Beyond Melksham we're frequently on jobs in Holt (BA14), Staverton (BA14), Trowbridge (BA14) and Bromham (SN15) — so spares, follow-ups and annual services are straightforward.

What backs up a Melksham quote

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Checkatrade 9.9/10

362+ verified reviews from real customers across BA and BS postcodes.

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

Local, family-run

Based at 24 Bristol Rd, Radstock — every job is run by the team that quoted it.

How we run gas boiler installation on site

Gas Safe registered engineers
Free no-obligation quotes
Smart heating controls fitted
Conversions (regular to combi)
Free written quote, no obligation
Local aftercare from a 12-mile base

Common queries, answered honestly

As a landlord, how quickly can you deal with a no-heat call for a tenant?: We book calls in during our published hours, Monday to Friday 8:30 to 5, and don't operate an out-of-hours emergency line, so we're upfront that a weekend no-heat call will wait until the next working day unless you've other cover in place. During the week we prioritise no-heat and no-hot-water calls where we can.
What is condensate and why does its routing matter?: Condensate is the mildly acidic water produced by a modern condensing boiler as it extracts extra heat from the flue gases, and it needs a route to an internal drain or, less ideally, an external soakaway. In colder or more exposed locations an external condensate pipe can freeze and shut the boiler down, so internal routing is worth prioritising where the layout allows it.
Is a boiler install a noisy, disruptive job?: There's unavoidable noise — drilling for the flue, pipework, sometimes moving a cylinder — but a straightforward swap is usually done within a working day with the mess kept to the immediate work area. We dust-sheet the route in and out and clear away pipe offcuts and old parts before we leave.
Is it worth upgrading the heating controls when we replace the boiler?: Where the existing controls are an old mechanical timer and single room thermostat, replacing them alongside the boiler with weather compensation or a modern programmable thermostat usually improves comfort and efficiency more than the boiler swap alone. It's not compulsory, but it's often the single best-value addition to a new install.
How do you decide whether to repair or replace a boiler?: We weigh the age of the boiler, whether parts are still made for it, how many faults it's had recently, and its running efficiency against a like-for-like or upgraded replacement. If a straightforward part fixes it and the boiler's otherwise sound, we'll say so rather than push a new install you don't need.
Do you cover all of Melksham?: Yes — every street in SN12 that falls under Melksham, plus the lanes towards Holt and Staverton. We're 12 miles away in Radstock, so most jobs are reached in well under half an hour.

Booking work in Melksham

If you're not in a rush, arranging gas boiler installation outside the depths of winter usually means more flexibility on scheduling and a calmer job overall. If you are in a rush because something's already failed, tell us that when you call so we can prioritise accordingly within our normal working hours. Send the appliance make, model and any fault code and you get a straight answer, not a sales script. Nearest neighbours on our round are Holt, Staverton, Trowbridge. Most of what we open up here is victorian terraces and modern estates, which dictates flue routes and pipe sizing.

07516 118198 All services in Melksham

The factual picture in Melksham

County: Wiltshire
Postcode district: SN12
Settlement type: town
Nearest classified road: A350
Distance from our base: 12 miles (Radstock, BA3)
Typical building stock: Victorian terraces and modern estates
Water hardness: moderately hard water
Fuel availability: mains gas across most of the area
Customer mix: a mix of owner-occupied and rented homes
Nearby areas covered: Holt, Staverton, Trowbridge, Bromham

Practical considerations across SN12

Common boiler fault codes and what usually causes them

Most modern boilers display a fault code on the control panel when they lock out, and while the exact code differs between manufacturers, the underlying causes cluster into a small number of categories: low system pressure (often from a small leak or after bleeding radiators), ignition failure (a worn electrode, gas supply issue, or blocked condensate causing a safety shutdown), or a failed sensor reporting an implausible temperature reading. A condensate blockage or freeze specifically tends to show a distinct code from a genuine ignition fault, which is why checking the external condensate pipe for ice before calling out an engineer in a cold snap can sometimes resolve the issue without a visit at all. We ask for the exact fault code and any recent history — a bled radiator, a cold snap, a recent service — before attending, since it often narrows down the likely cause before we arrive.

Working across Wiltshire: what being local changes

Being based at 24 Bristol Road, Radstock, 12 miles from Melksham via the A350, means a callout doesn't involve a long cross-county drive, and it also means familiarity with the recurring patterns in the local building stock — victorian terraces and modern estates — rather than encountering that construction type for the first time on-site. Local knowledge doesn't replace a proper site survey, but it does mean fewer surprises: knowing in advance that a particular postcode area typically has hard water, older single-pipe circuits, or restricted parking means the quote reflects the likely reality of the job before the first visit. We're Gas Safe and OFTEC registered and work across Wiltshire on that basis, not by claiming coverage we don't actually deliver on.

Condensate pipe freezing on exposed elevations

Properties on the higher ground around Melksham catch more wind chill than the valley floor, and an external condensate pipe on a north or east-facing wall is the most common cause of a boiler lockout in a cold snap. The pipe carries mildly acidic waste water from the flue; if it's routed externally in 21.5mm pipe rather than run internally and lagged, or dropped into an internal soil stack, it freezes solid and the boiler senses a blockage and shuts down for safety. Building Regulations guidance favours an internal run with a trapped connection to the waste system wherever the layout allows it. Where an external run is unavoidable we use 32mm insulated pipe with a minimal fall, which resists freezing far better than the standard diameter.

Melksham's A350 corridor and what it means for scheduling

Properties along or near the A350 corridor around Melksham are generally straightforward to reach without the access constraints of side lanes or unclassified roads further off the main network, which helps with scheduling deliveries of boilers, cylinders or oil tanks to a fixed slot. It doesn't change the technical requirements of the job itself, but predictable access does mean less contingency time needs building into a visit, and it makes coordinating a delivery with an installation date more reliable than on a property with a difficult final approach. We still confirm any specific parking or loading restriction on the immediate street before a job, since a fast main road doesn't guarantee easy stopping right outside the property.

How a condensing boiler recovers extra heat

A condensing boiler passes flue gases through a secondary heat exchanger before they leave the flue, extracting additional heat by condensing water vapour in the exhaust back into liquid, which is expelled as the mildly acidic condensate water down the drain. This is why every condensing boiler needs a condensate drainage route as part of its installation, unlike older non-condensing boilers, which simply vented hot dry gas straight out. The efficiency benefit only fully materialises when the boiler is actually condensing regularly, which needs a return water temperature low enough — generally below 55°C — for water vapour to condense in the first place. A condensing boiler run permanently at a high flow temperature can spend much of its time not actually condensing, which is one of the main reasons flow temperature settings matter as much as the boiler model chosen.

Mixed owner-occupied and rented housing in Melksham

Melksham's mix of owner-occupied and rented housing means we regularly work to two different sets of expectations on the same street — a landlord wanting the minimum reliable, compliant system at reasonable cost for a tenanted property, and an owner-occupier next door wanting a longer-term investment in efficiency and comfort. Both are legitimate priorities, but they lead to different specifications: a landlord's replacement boiler decision is often driven by the annual gas safety record and reliable compliance, while an owner-occupier's decision more often factors in flow temperature optimisation and controls for their own daily comfort. We ask which category a job falls into early, since it changes the questions worth asking about the property and the recommendation that follows.

Other boiler services in Melksham

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote