What does "commissioning" a boiler actually involve?

Commissioning is setting the boiler up correctly for the property rather than just switching it on: checking gas or oil pressure and flow rates, setting flow temperatures, testing safety devices, balancing the system, and completing the manufacturer's Benchmark checklist. Skipping this properly is one of the most common reasons warranty claims get refused later.

What's actually checked during an annual boiler service?

A service includes a visual and functional check of the boiler's casing and controls, flue gas analysis to confirm safe and efficient combustion, checking the flame picture and pressure, inspecting seals and condensate, and testing safety devices. It's a safety check as much as a performance one, and it's what keeps most manufacturer warranties valid.

Is a boiler install a noisy, disruptive job?

There's unavoidable noise — drilling for the flue, pipework, sometimes moving a cylinder — but a straightforward swap is usually done within a working day with the mess kept to the immediate work area. We dust-sheet the route in and out and clear away pipe offcuts and old parts before we leave.

Where can a new boiler actually be sited in the property?

A combi is usually fitted in a kitchen cupboard, utility room, loft, or garage as long as flue clearances to windows, doors, and boundaries are met. A system or regular boiler with a cylinder needs a bit more room and usually stays close to its current position unless you're relocating the whole system, which is a bigger job.

What paperwork do I get once the job's finished?

You'll get a Benchmark commissioning checklist for the boiler, a building notice or Building Control completion certificate for notifiable work, manufacturer warranty registration confirmation, and a Gas Safe (or OFTEC) record of the work. Keep these together — they're what a future buyer's solicitor or a warranty claim will ask for.

What's the warranty on a new boiler installed in Melksham?

Up to 10 years on qualifying Worcester Bosch installs registered through us as Accredited Installers. Other manufacturers typically offer 5–7 years.

Local Oil Tank Replacement for Melksham

Some properties make oil tank replacement straightforward; others need a bit more thought about parking, access to the boiler cupboard, or how equipment gets in and out. We factor that into the visit rather than discovering it on the day. Working from 24 Bristol Road, Radstock BA3 3EE across the Radstock, Bath and Mendip area, we're Gas Safe registered and OFTEC registered, so both mains gas and oil-fired work is covered under one roof. a mix of owner-occupied and rented homes make up most enquiries from this postcode.

07516 118198 Book a survey

SN12 · Wiltshire · 12 mi from Radstock · A350

Gas-fired appliance serving a hill top property near Melksham — hill top setting

Reading the property before pricing the work

Most properties in this settlement sit on the mains gas network, which keeps the fuel choice straightforward and generally opens up the widest range of boiler options. That doesn't remove every complication — flue routing, existing pipework diameter and how the property currently distributes heat still need checking — but it does mean the conversation usually starts from a simpler baseline than in the off-grid villages further out. We're Gas Safe registered for exactly this kind of work. Access is open suburban, so parking, spoil removal and delivery timing get planned in advance. Melksham is roughly 12 miles from our Radstock base via the A350. Typical property stock here: Victorian terraces and modern estates. Mains gas covers most of Melksham, so the usual choice is between a modern combi or a system boiler with a cylinder — we'll size it correctly for the home, not just swap like-for-like. Repair calls in Melksham usually get a same-week visit, with most common faults fixed on the first attempt.

Where else we work near Melksham

Beyond Melksham we're frequently on jobs in Holt (BA14), Staverton (BA14), Trowbridge (BA14) and Bromham (SN15) — so spares, follow-ups and annual services are straightforward.

What oil tank replacement includes here

Bunded plastic and steel tanks supplied
Base preparation and safe siting distances
New supply line, filter and fire valve
Old tank drained and removed
Free written quote, no obligation
Local aftercare from a 12-mile base

Qualifications behind the work

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Local, family-run

Based at 24 Bristol Rd, Radstock — every job is run by the team that quoted it.

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

Checkatrade 9.9/10

362+ verified reviews from real customers across BA and BS postcodes.

Melksham questions we get asked

What does "commissioning" a boiler actually involve?: Commissioning is setting the boiler up correctly for the property rather than just switching it on: checking gas or oil pressure and flow rates, setting flow temperatures, testing safety devices, balancing the system, and completing the manufacturer's Benchmark checklist. Skipping this properly is one of the most common reasons warranty claims get refused later.
What's actually checked during an annual boiler service?: A service includes a visual and functional check of the boiler's casing and controls, flue gas analysis to confirm safe and efficient combustion, checking the flame picture and pressure, inspecting seals and condensate, and testing safety devices. It's a safety check as much as a performance one, and it's what keeps most manufacturer warranties valid.
Is a boiler install a noisy, disruptive job?: There's unavoidable noise — drilling for the flue, pipework, sometimes moving a cylinder — but a straightforward swap is usually done within a working day with the mess kept to the immediate work area. We dust-sheet the route in and out and clear away pipe offcuts and old parts before we leave.
Where can a new boiler actually be sited in the property?: A combi is usually fitted in a kitchen cupboard, utility room, loft, or garage as long as flue clearances to windows, doors, and boundaries are met. A system or regular boiler with a cylinder needs a bit more room and usually stays close to its current position unless you're relocating the whole system, which is a bigger job.
What paperwork do I get once the job's finished?: You'll get a Benchmark commissioning checklist for the boiler, a building notice or Building Control completion certificate for notifiable work, manufacturer warranty registration confirmation, and a Gas Safe (or OFTEC) record of the work. Keep these together — they're what a future buyer's solicitor or a warranty claim will ask for.
What's the warranty on a new boiler installed in Melksham?: Up to 10 years on qualifying Worcester Bosch installs registered through us as Accredited Installers. Other manufacturers typically offer 5–7 years.

Booking work in Melksham

Once we've seen the property, you'll get a written quote for oil tank replacement that sets out exactly what's included — the equipment, the work, and what happens if anything unexpected turns up once we're on site. That gives you something concrete to compare against any other quotes you're getting. Call 07516 118198 and we will confirm a visit slot for SN12. Most of what we open up here is victorian terraces and modern estates, which dictates flue routes and pipe sizing.

07516 118198 All services in Melksham

Coverage detail for SN12

County: Wiltshire
Postcode district: SN12
Settlement type: town
Nearest classified road: A350
Distance from our base: 12 miles (Radstock, BA3)
Typical building stock: Victorian terraces and modern estates
Water hardness: moderately hard water
Fuel availability: mains gas across most of the area
Customer mix: a mix of owner-occupied and rented homes
Nearby areas covered: Holt, Staverton, Trowbridge, Bromham

Practical considerations across SN12

Pumped-oil versus gravity feed: does it matter?

Older oil systems sometimes still rely on gravity feed, where the tank sits higher than the burner and oil flows down to it under its own weight; a pumped system uses the burner's internal pump to draw oil up from a tank at any level, including below the boiler. Gravity feed limits where a tank can be sited and is more prone to airlocks if the line runs dry, while a pumped system is more flexible on tank position but needs the pipe run and lift height kept within the burner pump's rated capacity — usually no more than a few metres of lift and a set maximum run length. When we replace an oil boiler we check which type the existing tank and pipework support before assuming a straight swap, because a tank sited for gravity feed may need repositioning or a different pump to suit a modern burner.

Oil tank de-sludging: why it's not optional

Oil sitting in a tank for years accumulates water from condensation and fine sediment that settles at the bottom, and over time this forms a sludge layer that can be drawn into the fuel line, particularly when the tank is nearly empty and the outlet pulls from lower in the tank than usual. Sludge blocks fine oil filters and burner nozzles, which shows up as burner lockouts or a boiler that won't fire cleanly rather than as an obvious tank problem. De-sludging drains and cleans the tank base without necessarily removing the whole tank, and it's worth doing when a tank is inherited with a property, before switching to a new boiler, or if lockouts recur despite the filter and nozzle being replaced. It's a preventative job that's cheaper done on schedule than after a burner failure it caused.

Extra wind exposure on hilltop properties and what it means for heating

Elevated sites around Melksham lose heat faster through infiltration in windy weather than a sheltered valley property of identical construction, because wind pressure drives more cold air through gaps around doors, windows and loft hatches. This shows up as a heating system working harder to maintain the same internal temperature on a windy but not especially cold day than a still, colder one — a pattern that can look like an underperforming boiler when the real cause is draught infiltration. It also affects flue performance: an exposed terminal position can experience more downdraught, which is one reason correct terminal siting and, where needed, terminal guards matter more on hilltop sites than sheltered ones. We factor exposure into heat loss assumptions on elevated properties rather than using a flat regional design temperature.

How a condensing boiler recovers extra heat

A condensing boiler passes flue gases through a secondary heat exchanger before they leave the flue, extracting additional heat by condensing water vapour in the exhaust back into liquid, which is expelled as the mildly acidic condensate water down the drain. This is why every condensing boiler needs a condensate drainage route as part of its installation, unlike older non-condensing boilers, which simply vented hot dry gas straight out. The efficiency benefit only fully materialises when the boiler is actually condensing regularly, which needs a return water temperature low enough — generally below 55°C — for water vapour to condense in the first place. A condensing boiler run permanently at a high flow temperature can spend much of its time not actually condensing, which is one of the main reasons flow temperature settings matter as much as the boiler model chosen.

Signs a boiler repair is no longer the right call

A boiler that's failing repeatedly, needing a different part replaced every service, or over roughly ten to fifteen years old is approaching the point where continued repair costs more over time than replacement, particularly once a heat exchanger — the most expensive single part — starts to show signs of failure through leaks or reduced output. Efficiency is the other half of the calculation: an older non-condensing boiler running at 70-80% efficiency against a modern condensing combi at over 90% means a meaningful chunk of every unit of fuel burned in the old boiler is simply lost up the flue. We give a straight answer on repair versus replace based on the fault found and the boiler's age and condition, rather than defaulting to whichever is more profitable to us on the day.

Working across Wiltshire: what being local changes

Being based at 24 Bristol Road, Radstock, 12 miles from Melksham via the A350, means a callout doesn't involve a long cross-county drive, and it also means familiarity with the recurring patterns in the local building stock — victorian terraces and modern estates — rather than encountering that construction type for the first time on-site. Local knowledge doesn't replace a proper site survey, but it does mean fewer surprises: knowing in advance that a particular postcode area typically has hard water, older single-pipe circuits, or restricted parking means the quote reflects the likely reality of the job before the first visit. We're Gas Safe and OFTEC registered and work across Wiltshire on that basis, not by claiming coverage we don't actually deliver on.

Other boiler services in Melksham

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote