What actually happens on install day?

The engineer isolates the gas or oil supply and water, removes the old boiler, fits and pressure-tests the new one, connects the flue and condensate, and commissions the system. For a straight swap this is usually one day; a conversion, relocation, or cylinder change can run into a second depending on the pipework involved.

How often should a boiler actually be serviced?

Once a year is the standard recommendation from every manufacturer, and most warranty terms make it a condition rather than a suggestion — miss a year and a claim can be refused even if the fault is unrelated. Landlords have a separate legal duty to have gas appliances checked annually regardless of warranty terms.

What paperwork do I get once the job's finished?

You'll get a Benchmark commissioning checklist for the boiler, a building notice or Building Control completion certificate for notifiable work, manufacturer warranty registration confirmation, and a Gas Safe (or OFTEC) record of the work. Keep these together — they're what a future buyer's solicitor or a warranty claim will ask for.

Do I need to do anything to activate my boiler's warranty?

As a Worcester Bosch Accredited Installer we register qualifying Worcester installs on your behalf, which is what unlocks the extended guarantee (up to 10 years* on qualifying installs) rather than the standard shorter term. For other brands we still register the installation; keep the confirmation with your other paperwork in case you need it.

What's a CP12 and do I need one as a landlord?

A CP12 (Landlord Gas Safety Record) confirms every gas appliance in a rented property has passed an annual safety check by a Gas Safe registered engineer. It's a legal requirement before letting and at each renewal, a copy has to go to tenants, and it needs to be renewed every 12 months without a gap.

Will you come out to a village like Croscombe?

Croscombe is part of our core patch (9 miles from base via the A371). Same-week site visits and quick callbacks are normal.

Croscombe's Local Oil Boiler Servicing Specialist

Timing matters with oil boiler servicing: a mid-summer replacement gives more room to plan than an emergency swap in January, and a written quote gives you time to think rather than decide under pressure. We can work to either, but a bit of notice usually means a smoother job. Gas Safe registered, OFTEC registered, 24 Bristol Road, Radstock BA3 3EE, open Monday to Friday, 8:30am to 5pm. Our van runs the A371 to reach you, 9 miles out from the Radstock workshop.

07516 118198 Ask about the guarantee

BA5 · Somerset · 9 mi from Radstock · A371

Boiler work underway on stone cottages and listed buildings near Croscombe — level setting

Also covering the lanes around Croscombe

Beyond Croscombe we're frequently on jobs in Wells (BA5), Pilton (BA4), Shepton Mallet (BA4) and Dinder (BA5) — so spares, follow-ups and annual services are straightforward.

What oil boiler servicing includes here

OFTEC registered oil specialist
Nozzle, electrode and fuel filter renewed
Smoke test and pump pressure set correctly
Oil tank and supply line inspected
Free written quote, no obligation
Local aftercare from a 9-mile base

How Somerset building stock shapes the spec

This area has a genuine mix of mains gas and oil-fired properties, sometimes on the same street, depending on when the gas network reached that particular row of houses. It's worth confirming which fuel your property is actually on and whether a fuel switch is realistic before assuming either option is off the table. Being registered for both Gas Safe and OFTEC work means we can look at the honest options for your specific property rather than steering you toward whichever fuel we happen to be set up for. Water here is moderately hard water, so scale protection is specified accordingly. Croscombe is roughly 9 miles from our Radstock base via the A371. Typical property stock here: stone cottages and listed buildings. A meaningful share of properties around Croscombe are off the gas grid, so oil boiler installs and tank swaps make up a fair part of what we do locally. Repair calls in Croscombe usually get a same-week visit, with most common faults fixed on the first attempt.

Proof, paperwork and accountability

Local, family-run

Based at 24 Bristol Rd, Radstock — every job is run by the team that quoted it.

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

Fixed written prices

No verbal-only quotes. You'll get the boiler model, controls and warranty in writing before we book.

Croscombe questions we get asked

What actually happens on install day?: The engineer isolates the gas or oil supply and water, removes the old boiler, fits and pressure-tests the new one, connects the flue and condensate, and commissions the system. For a straight swap this is usually one day; a conversion, relocation, or cylinder change can run into a second depending on the pipework involved.
How often should a boiler actually be serviced?: Once a year is the standard recommendation from every manufacturer, and most warranty terms make it a condition rather than a suggestion — miss a year and a claim can be refused even if the fault is unrelated. Landlords have a separate legal duty to have gas appliances checked annually regardless of warranty terms.
What paperwork do I get once the job's finished?: You'll get a Benchmark commissioning checklist for the boiler, a building notice or Building Control completion certificate for notifiable work, manufacturer warranty registration confirmation, and a Gas Safe (or OFTEC) record of the work. Keep these together — they're what a future buyer's solicitor or a warranty claim will ask for.
Do I need to do anything to activate my boiler's warranty?: As a Worcester Bosch Accredited Installer we register qualifying Worcester installs on your behalf, which is what unlocks the extended guarantee (up to 10 years* on qualifying installs) rather than the standard shorter term. For other brands we still register the installation; keep the confirmation with your other paperwork in case you need it.
What's a CP12 and do I need one as a landlord?: A CP12 (Landlord Gas Safety Record) confirms every gas appliance in a rented property has passed an annual safety check by a Gas Safe registered engineer. It's a legal requirement before letting and at each renewal, a copy has to go to tenants, and it needs to be renewed every 12 months without a gap.
Will you come out to a village like Croscombe?: Croscombe is part of our core patch (9 miles from base via the A371). Same-week site visits and quick callbacks are normal.

Where to go from here

Once we've seen the property, you'll get a written quote for oil boiler servicing that sets out exactly what's included — the equipment, the work, and what happens if anything unexpected turns up once we're on site. That gives you something concrete to compare against any other quotes you're getting. Call 07516 118198 and we will confirm a visit slot for BA5. Most of what we open up here is stone cottages and listed buildings, which dictates flue routes and pipe sizing.

07516 118198 All services in Croscombe

Croscombe at a glance

County: Somerset
Postcode district: BA5
Settlement type: village
Nearest classified road: A371
Distance from our base: 9 miles (Radstock, BA3)
Typical building stock: stone cottages and listed buildings
Water hardness: moderately hard water
Fuel availability: mains gas with off-grid pockets
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Wells, Pilton, Shepton Mallet, Dinder

Things we check around Croscombe

Do you need listed building consent for a new flue?

Whether a new boiler flue on a listed building in or around Croscombe needs formal listed building consent depends on whether the work affects the building's special architectural or historic character — cutting through an original stone wall or a decorative elevation is far more likely to need consent than routing through a later, non-original extension. Consent has to be granted before the work starts; carrying it out first and applying afterwards is a criminal offence under the Planning (Listed Buildings and Conservation Areas) Act, not just a paperwork formality to tidy up later. We recommend checking with the local planning authority's conservation team at the quoting stage on any listed property, because the answer varies by building and by exactly which wall is proposed, and getting it wrong can mean expensive remedial work to satisfy the authority afterwards.

Pumped-oil versus gravity feed: does it matter?

Older oil systems sometimes still rely on gravity feed, where the tank sits higher than the burner and oil flows down to it under its own weight; a pumped system uses the burner's internal pump to draw oil up from a tank at any level, including below the boiler. Gravity feed limits where a tank can be sited and is more prone to airlocks if the line runs dry, while a pumped system is more flexible on tank position but needs the pipe run and lift height kept within the burner pump's rated capacity — usually no more than a few metres of lift and a set maximum run length. When we replace an oil boiler we check which type the existing tank and pipework support before assuming a straight swap, because a tank sited for gravity feed may need repositioning or a different pump to suit a modern burner.

Choosing a boiler location that satisfies both planning and practicality in Croscombe

On a property within a conservation area, AONB or World Heritage designation, the boiler's physical location is often decided as much by the acceptable flue route as by where the homeowner would naturally put it — a kitchen wall facing the street may need ruling out even before considering pipe run length, simply because the flue outlet would be visible from a protected streetscape. Working back from an acceptable flue position to find a viable boiler location sometimes means a longer pipework run through the property than would otherwise be chosen, adding to the job's cost and complexity. We assess planning constraints on the flue before finalising the boiler's proposed location, rather than picking the location first and discovering the flue route is unacceptable afterwards.

Low-loss headers on larger or multi-zone systems

On a system with several heating zones or a boiler oversized relative to any single zone's flow requirement, a low-loss header hydraulically separates the boiler's primary circuit from the secondary zone circuits, so each side can run its own pump and flow rate without one interfering with the other. Without it, a zone valve closing on a multi-zone system can starve the boiler of flow or force excessive pump pressure through the remaining open zones. It's most relevant on larger properties or ones with commercial premises attached, where several distinct heating circuits — perhaps a shop unit and a flat above — share one heat source. Getting the header sized to the boiler's actual flow rate, not just fitted as standard, is what makes it work rather than just adding another connection.

Croscombe's place within the wider Somerset area we cover

Croscombe is one of several neighbourhoods we work in around the wider area, and while the postcode district and general water hardness and building stock trends are shared with the surrounding district, the specific street-level access, parking and property type still varies enough locally that we treat each visit on its own facts rather than applying a generic area answer. Nearby areas we also cover include Wells, Pilton and Shepton Mallet, which is relevant mainly where a customer wants comparable jobs referenced or where a single visit can sensibly cover more than one nearby property in the same trip. The underlying trade standards — Gas Safe, OFTEC, correct commissioning — don't vary by neighbourhood, only the practical details of the job do.

Chimney liners for boilers using an existing flue

Where an older boiler used the property's original brick or stone chimney as its flue route, a replacement condensing boiler usually can't use the same masonry flue unlined, because the flue gases are cooler and wetter and will attack unprotected brickwork and mortar over time. A correctly specified stainless steel liner, sized to the boiler manufacturer's flue length and diameter tables, carries the flue gases safely and lets the existing chimney be reused rather than needing a new wall or roof penetration — often the only realistic option on a listed or solid-wall property in Croscombe where an external flue run isn't permitted. The liner has to be inspected and swept as part of ongoing servicing exactly as an open-fire flue would be, which is easy to overlook once it's hidden inside the chimney.

Condensate soakaways where there's no convenient drain

Properties without a nearby internal waste connection or external gully for the boiler's condensate — common on rural plots around Croscombe where the nearest drain run is a long way from the boiler's location — sometimes need a dedicated condensate soakaway instead. This is a small pit filled with granular material that the condensate, which is mildly acidic, can disperse into gradually rather than running to a drain at all. Sizing and siting it correctly matters: it needs to be far enough from foundations and sited where the local ground can actually absorb the modest but steady volume a boiler produces, particularly over a long heating season. Where ground conditions make a soakaway unreliable, running a longer insulated pipe to a proper drainage connection is usually the safer long-term choice even though it's more work to install.

Plume management kits for restricted flue positions

Where the ideal, shortest flue route would discharge too close to a boundary, a window, or onto a neighbouring property — a common constraint on tight plots in Croscombe — a plume management kit extends the flue's discharge point away from the boiler's own wall penetration, directing the visible water vapour plume and flue gases to a compliant location instead. It adds ductwork and sometimes a small additional fan to overcome the extra resistance, and it has to be specified against the specific boiler's approved kit range rather than improvised, since flue certification only covers tested combinations. It's a legitimate way to fit a boiler on a plot where the compliant flue route and the sensible boiler location aren't the same wall, without compromising on clearances to solve it.

Other boiler services in Croscombe

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote