We're a home attached to or near a small business premises — do you cover that kind of property?

Where the heating system is a standard domestic boiler serving living accommodation, it's within our normal scope even if it sits next to or above a shop or workshop, which is a common layout around Croscombe. Fully commercial systems and appliances are a different scope, so we'd confirm exactly what's being asked at enquiry stage.

How do you decide whether to repair or replace a boiler?

We weigh the age of the boiler, whether parts are still made for it, how many faults it's had recently, and its running efficiency against a like-for-like or upgraded replacement. If a straightforward part fixes it and the boiler's otherwise sound, we'll say so rather than push a new install you don't need.

Can you look over a quote I've already had from another company?

Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.

What actually happens on install day?

The engineer isolates the gas or oil supply and water, removes the old boiler, fits and pressure-tests the new one, connects the flue and condensate, and commissions the system. For a straight swap this is usually one day; a conversion, relocation, or cylinder change can run into a second depending on the pipework involved.

Who actually carries out the work?

A Gas Safe and, where relevant, OFTEC registered engineer from our own small team carries out the job — we don't sub the install out to a third party after quoting. You deal with the same people from survey through to commissioning and any aftercare calls.

How much longer does a full conversion take compared to a straight boiler swap?

A straight like-for-like swap in the same location is typically a single working day. Converting boiler type (for example back boiler to combi, or oil to LPG), relocating the boiler, or adding a new cylinder usually needs one to two extra days for additional pipework, flue routing, and electrical work, which we'll scope out at survey.

Oil Tank Replacement — Croscombe (BA5)

There's not much mystery to oil tank replacement done properly: a site visit to see the property, a written quote that sets out exactly what's included, and work carried out by a registered engineer who takes responsibility for it. That's how we run things from 24 Bristol Road, Radstock BA3 3EE, as a Gas Safe registered and OFTEC registered business open Monday to Friday, 8:30am to 5pm. Access is lane access, so parking, spoil removal and delivery timing get planned in advance.

07516 118198 Discuss your property

BA5 · Somerset · 9 mi from Radstock · A371

Oil Tank Replacement in a mixed-cottage property in Croscombe, BA5 — level setting

The work, step by step

Bunded plastic and steel tanks supplied
Base preparation and safe siting distances
New supply line, filter and fire valve
Old tank drained and removed
Free written quote, no obligation
Local aftercare from a 9-mile base

Site realities in and around Croscombe

Conservation area status, and in Bath's case UNESCO World Heritage designation, adds a layer of consideration to anything visible from the street, particularly flue positions and external pipework. It doesn't rule out a straightforward boiler replacement, but it does mean the survey needs to look properly at routing options that keep the installation discreet and compliant. We flag this at quote stage rather than after the work has started, so there are no surprises about what can and can't be fitted where. Access is lane access, so parking, spoil removal and delivery timing get planned in advance. Croscombe is roughly 9 miles from our Radstock base via the A371. Typical property stock here: stone cottages and listed buildings. A meaningful share of properties around Croscombe are off the gas grid, so oil boiler installs and tank swaps make up a fair part of what we do locally. Repair calls in Croscombe usually get a same-week visit, with most common faults fixed on the first attempt.

Proof, paperwork and accountability

Fixed written prices

No verbal-only quotes. You'll get the boiler model, controls and warranty in writing before we book.

Checkatrade 9.9/10

362+ verified reviews from real customers across BA and BS postcodes.

Worcester Bosch Accredited

Qualifies your install for the full 10-year manufacturer guarantee* on supported models.

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Also covering the lanes around Croscombe

Beyond Croscombe we're frequently on jobs in Wells (BA5), Pilton (BA4), Shepton Mallet (BA4) and Dinder (BA5) — so spares, follow-ups and annual services are straightforward.

Croscombe questions we get asked

We're a home attached to or near a small business premises — do you cover that kind of property?: Where the heating system is a standard domestic boiler serving living accommodation, it's within our normal scope even if it sits next to or above a shop or workshop, which is a common layout around Croscombe. Fully commercial systems and appliances are a different scope, so we'd confirm exactly what's being asked at enquiry stage.
How do you decide whether to repair or replace a boiler?: We weigh the age of the boiler, whether parts are still made for it, how many faults it's had recently, and its running efficiency against a like-for-like or upgraded replacement. If a straightforward part fixes it and the boiler's otherwise sound, we'll say so rather than push a new install you don't need.
Can you look over a quote I've already had from another company?: Yes, this comes up often. Send or bring in the other written quote and we'll go through the spec — boiler size, controls, cylinder if included, and what's actually listed for parts and labour — and tell you plainly whether it looks right for the property, oversized, or missing something we'd expect to see.
What actually happens on install day?: The engineer isolates the gas or oil supply and water, removes the old boiler, fits and pressure-tests the new one, connects the flue and condensate, and commissions the system. For a straight swap this is usually one day; a conversion, relocation, or cylinder change can run into a second depending on the pipework involved.
Who actually carries out the work?: A Gas Safe and, where relevant, OFTEC registered engineer from our own small team carries out the job — we don't sub the install out to a third party after quoting. You deal with the same people from survey through to commissioning and any aftercare calls.
How much longer does a full conversion take compared to a straight boiler swap?: A straight like-for-like swap in the same location is typically a single working day. Converting boiler type (for example back boiler to combi, or oil to LPG), relocating the boiler, or adding a new cylinder usually needs one to two extra days for additional pipework, flue routing, and electrical work, which we'll scope out at survey.

Where to go from here

If oil tank replacement is something you're looking into, the simplest next step is a call on 07516 118198 during our normal hours, Monday to Friday, 8:30am to 5pm. Tell us a bit about the property and what's prompted the enquiry, and we'll take it from there. A written quote follows the survey — no pressure, and no charge for the Croscombe visit. Most of what we open up here is stone cottages and listed buildings, which dictates flue routes and pipe sizing.

07516 118198 All services in Croscombe

Coverage detail for BA5

County: Somerset
Postcode district: BA5
Settlement type: village
Nearest classified road: A371
Distance from our base: 9 miles (Radstock, BA3)
Typical building stock: stone cottages and listed buildings
Water hardness: moderately hard water
Fuel availability: mains gas with off-grid pockets
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Wells, Pilton, Shepton Mallet, Dinder

Practical considerations across BA5

Pumped-oil versus gravity feed: does it matter?

Older oil systems sometimes still rely on gravity feed, where the tank sits higher than the burner and oil flows down to it under its own weight; a pumped system uses the burner's internal pump to draw oil up from a tank at any level, including below the boiler. Gravity feed limits where a tank can be sited and is more prone to airlocks if the line runs dry, while a pumped system is more flexible on tank position but needs the pipe run and lift height kept within the burner pump's rated capacity — usually no more than a few metres of lift and a set maximum run length. When we replace an oil boiler we check which type the existing tank and pipework support before assuming a straight swap, because a tank sited for gravity feed may need repositioning or a different pump to suit a modern burner.

Heating where a home sits alongside commercial premises

Properties around Croscombe that combine living accommodation with an attached shop, workshop or other commercial space often need heating designed as genuinely separate zones with independent controls, since a shop's occupied hours and heating demand rarely match the flat or house above it. Where the two shared a single ageing system, splitting them onto separate zone valves — or, on a larger scale, separate boilers — stops one side subsidising or interfering with the other's heating schedule. Commercial space also sometimes falls under different servicing and safety-record obligations than the residential side, depending on how it's used, so it's worth establishing which parts of the building fall under which regime before assuming a single annual service covers everything.

Working across Somerset: what being local changes

Being based at 24 Bristol Road, Radstock, 9 miles from Croscombe via the A371, means a callout doesn't involve a long cross-county drive, and it also means familiarity with the recurring patterns in the local building stock — stone cottages and listed buildings — rather than encountering that construction type for the first time on-site. Local knowledge doesn't replace a proper site survey, but it does mean fewer surprises: knowing in advance that a particular postcode area typically has hard water, older single-pipe circuits, or restricted parking means the quote reflects the likely reality of the job before the first visit. We're Gas Safe and OFTEC registered and work across Somerset on that basis, not by claiming coverage we don't actually deliver on.

Do you need listed building consent for a new flue?

Whether a new boiler flue on a listed building in or around Croscombe needs formal listed building consent depends on whether the work affects the building's special architectural or historic character — cutting through an original stone wall or a decorative elevation is far more likely to need consent than routing through a later, non-original extension. Consent has to be granted before the work starts; carrying it out first and applying afterwards is a criminal offence under the Planning (Listed Buildings and Conservation Areas) Act, not just a paperwork formality to tidy up later. We recommend checking with the local planning authority's conservation team at the quoting stage on any listed property, because the answer varies by building and by exactly which wall is proposed, and getting it wrong can mean expensive remedial work to satisfy the authority afterwards.

Routing a flue through a listed or conservation-area property

Croscombe falls within an area where listed building consent or conservation area rules can affect where a boiler flue is allowed to terminate — a plume on a principal elevation facing the street is often unacceptable even where it would technically clear manufacturer distances. Getting consent, where it's needed, has to happen before the flue is cut through a wall, not retrospectively. In practice this usually means routing the flue to a rear or side elevation even if that means a longer pipe run and an extra bend, or using a horizontal flue kit through a lower window reveal wall rather than the roof. We check with the relevant conservation officer's published guidance before quoting a flue route on a listed or Article 4 property rather than assuming the shortest run will be approved.

Nozzle replacement and baffle cleaning on oil burners

An oil burner's nozzle atomises fuel into a fine spray for combustion, and it wears from constant fuel flow at pressure, gradually changing the spray pattern away from the burner manufacturer's specification even before it visibly fails. A worn nozzle burns less cleanly, producing more soot that coats the heat exchanger's baffles, and a sooted heat exchanger loses efficiency in the same way scale does on a gas boiler's plates. Standard practice on an annual oil service is to replace the nozzle as a matter of course, rather than wait for a fault, and to remove and clean the baffles so the heat exchanger surfaces are exposed to combustion heat properly again. Skipping nozzle replacement to save a service visit's minor parts cost is a false economy against the fuel wasted by a poorly atomising burner.

Wood-burning stoves with a back boiler alongside a main boiler

Some older rural properties around Croscombe run a wood-burning stove with a back boiler feeding heat into the same central heating circuit as an oil or gas boiler, usually through a thermal store or a cylinder with two coils. Getting this combination to work safely means the stove's back boiler circuit has its own means of dissipating heat if the pump fails or a valve closes while the stove is still burning — a stove can't simply be switched off the way a boiler can if its heat has nowhere to go, so a gravity-fed safety circuit or heat leak radiator is normally required. It's a more involved design than a single-boiler system and needs planning at the point either appliance is replaced, not treated as an afterthought once the new boiler is already fitted.

Signs a boiler repair is no longer the right call

A boiler that's failing repeatedly, needing a different part replaced every service, or over roughly ten to fifteen years old is approaching the point where continued repair costs more over time than replacement, particularly once a heat exchanger — the most expensive single part — starts to show signs of failure through leaks or reduced output. Efficiency is the other half of the calculation: an older non-condensing boiler running at 70-80% efficiency against a modern condensing combi at over 90% means a meaningful chunk of every unit of fuel burned in the old boiler is simply lost up the flue. We give a straight answer on repair versus replace based on the fault found and the boiler's age and condition, rather than defaulting to whichever is more profitable to us on the day.

How a condensing boiler recovers extra heat

A condensing boiler passes flue gases through a secondary heat exchanger before they leave the flue, extracting additional heat by condensing water vapour in the exhaust back into liquid, which is expelled as the mildly acidic condensate water down the drain. This is why every condensing boiler needs a condensate drainage route as part of its installation, unlike older non-condensing boilers, which simply vented hot dry gas straight out. The efficiency benefit only fully materialises when the boiler is actually condensing regularly, which needs a return water temperature low enough — generally below 55°C — for water vapour to condense in the first place. A condensing boiler run permanently at a high flow temperature can spend much of its time not actually condensing, which is one of the main reasons flow temperature settings matter as much as the boiler model chosen.

Other boiler services in Croscombe

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote