Who actually carries out the work?

A Gas Safe and, where relevant, OFTEC registered engineer from our own small team carries out the job — we don't sub the install out to a third party after quoting. You deal with the same people from survey through to commissioning and any aftercare calls.

How much longer does a full conversion take compared to a straight boiler swap?

A straight like-for-like swap in the same location is typically a single working day. Converting boiler type (for example back boiler to combi, or oil to LPG), relocating the boiler, or adding a new cylinder usually needs one to two extra days for additional pipework, flue routing, and electrical work, which we'll scope out at survey.

Is a boiler install a noisy, disruptive job?

There's unavoidable noise — drilling for the flue, pipework, sometimes moving a cylinder — but a straightforward swap is usually done within a working day with the mess kept to the immediate work area. We dust-sheet the route in and out and clear away pipe offcuts and old parts before we leave.

Is it worth upgrading the heating controls when we replace the boiler?

Where the existing controls are an old mechanical timer and single room thermostat, replacing them alongside the boiler with weather compensation or a modern programmable thermostat usually improves comfort and efficiency more than the boiler swap alone. It's not compulsory, but it's often the single best-value addition to a new install.

Can your van get down our lane, or do we need to arrange something?

Most village lanes we work on are manageable in our vehicles, but if it's single-track, has a low bridge, or turning is tight, mention it when you book so we bring the right size van and allow extra time. It's rarely a reason to turn a job down, just something we plan around.

Our water's not as hard here — do we still need a power flush?

Water hardness affects scale, but sludge from years of corrosion and old radiators builds up regardless of hardness. If your system's been running a long time or you've had cold spots on radiators, a power flush before fitting a new boiler protects it just as much here as anywhere with harder water.

Boiler Servicing — Croscombe (BA5)

There's not much mystery to boiler servicing done properly: a site visit to see the property, a written quote that sets out exactly what's included, and work carried out by a registered engineer who takes responsibility for it. That's how we run things from 24 Bristol Road, Radstock BA3 3EE, as a Gas Safe registered and OFTEC registered business open Monday to Friday, 8:30am to 5pm. Most of what we open up here is stone cottages and listed buildings, which dictates flue routes and pipe sizing. Access is lane access, so parking, spoil removal and delivery timing get planned in advance. In Croscombe itself (BA5, Somerset) that usually means stone cottages and listed buildings, roughly 9 miles from the workshop.

07516 118198 Request your quote

BA5 · Somerset · 9 mi from Radstock · A371

Flue and pipework detail from a boiler servicing job in Somerset, boiler servicing in Croscombe (BA5) — lane access access

Nearby villages and neighbourhoods

Beyond Croscombe we're frequently on jobs in Wells (BA5), Pilton (BA4), Shepton Mallet (BA4) and Dinder (BA5) — so spares, follow-ups and annual services are straightforward.

What backs up a Croscombe quote

Gas Safe registered

Reg. 549918 — every gas job notified to Building Control and a CP12 issued where required.

Checkatrade 9.9/10

362+ verified reviews from real customers across BA and BS postcodes.

OFTEC trained

Oil boilers, oil tanks and pipework — fully certified for off-grid installs and replacements.

Local, family-run

Based at 24 Bristol Rd, Radstock — every job is run by the team that quoted it.

How we run boiler servicing on site

Full annual safety check
Landlord gas safety certificates
Efficiency report
Friendly, tidy engineers
Free written quote, no obligation
Local aftercare from a 9-mile base

Croscombe: stock, water and fuel supply

Stone cottages and farmhouses around here were mostly built long before central heating existed, so pipework and boiler locations have usually been retrofitted at some point, sometimes more than once. Thick stone walls, uneven floor levels and low ceilings can all affect where a boiler or cylinder can practically go, and older stonework doesn't always take fixings the way modern block or brick does. We work around those constraints on site rather than assuming a straightforward install. Terrain is level, which matters for condensate runs and tank siting. Nearest neighbours on our round are Wells, Pilton, Shepton Mallet. Croscombe is roughly 9 miles from our Radstock base via the A371. Typical property stock here: stone cottages and listed buildings. A meaningful share of properties around Croscombe are off the gas grid, so oil boiler installs and tank swaps make up a fair part of what we do locally. Annual services in Croscombe include a full safety check, efficiency report and warranty stamp where applicable.

Boiler Servicing FAQs for BA5

Who actually carries out the work?: A Gas Safe and, where relevant, OFTEC registered engineer from our own small team carries out the job — we don't sub the install out to a third party after quoting. You deal with the same people from survey through to commissioning and any aftercare calls.
How much longer does a full conversion take compared to a straight boiler swap?: A straight like-for-like swap in the same location is typically a single working day. Converting boiler type (for example back boiler to combi, or oil to LPG), relocating the boiler, or adding a new cylinder usually needs one to two extra days for additional pipework, flue routing, and electrical work, which we'll scope out at survey.
Is a boiler install a noisy, disruptive job?: There's unavoidable noise — drilling for the flue, pipework, sometimes moving a cylinder — but a straightforward swap is usually done within a working day with the mess kept to the immediate work area. We dust-sheet the route in and out and clear away pipe offcuts and old parts before we leave.
Is it worth upgrading the heating controls when we replace the boiler?: Where the existing controls are an old mechanical timer and single room thermostat, replacing them alongside the boiler with weather compensation or a modern programmable thermostat usually improves comfort and efficiency more than the boiler swap alone. It's not compulsory, but it's often the single best-value addition to a new install.
Can your van get down our lane, or do we need to arrange something?: Most village lanes we work on are manageable in our vehicles, but if it's single-track, has a low bridge, or turning is tight, mention it when you book so we bring the right size van and allow extra time. It's rarely a reason to turn a job down, just something we plan around.
Our water's not as hard here — do we still need a power flush?: Water hardness affects scale, but sludge from years of corrosion and old radiators builds up regardless of hardness. If your system's been running a long time or you've had cold spots on radiators, a power flush before fitting a new boiler protects it just as much here as anywhere with harder water.

Your next move in BA5

The next step for boiler servicing is a site visit, not a phone-only estimate. Seeing the property, the current system and the access lets us give you a figure that holds up once the work starts, rather than one that changes on the day. Call 07516 118198, Monday to Friday, 8:30am to 5pm, and we'll arrange a time that suits. Send the appliance make, model and any fault code and you get a straight answer, not a sales script. Water here is moderately hard water, so scale protection is specified accordingly. homes alongside small commercial and agricultural premises make up most enquiries from this postcode.

07516 118198 All services in Croscombe

The factual picture in Croscombe

County: Somerset
Postcode district: BA5
Settlement type: village
Nearest classified road: A371
Distance from our base: 9 miles (Radstock, BA3)
Typical building stock: stone cottages and listed buildings
Water hardness: moderately hard water
Fuel availability: mains gas with off-grid pockets
Customer mix: homes alongside small commercial and agricultural premises
Nearby areas covered: Wells, Pilton, Shepton Mallet, Dinder

Things we check around Croscombe

Nozzle replacement and baffle cleaning on oil burners

An oil burner's nozzle atomises fuel into a fine spray for combustion, and it wears from constant fuel flow at pressure, gradually changing the spray pattern away from the burner manufacturer's specification even before it visibly fails. A worn nozzle burns less cleanly, producing more soot that coats the heat exchanger's baffles, and a sooted heat exchanger loses efficiency in the same way scale does on a gas boiler's plates. Standard practice on an annual oil service is to replace the nozzle as a matter of course, rather than wait for a fault, and to remove and clean the baffles so the heat exchanger surfaces are exposed to combustion heat properly again. Skipping nozzle replacement to save a service visit's minor parts cost is a false economy against the fuel wasted by a poorly atomising burner.

LPG as an alternative to oil off the gas grid

Properties around Croscombe that sit off the mains gas network aren't limited to oil — bulk LPG, stored in an above-ground tank on a concrete base with the same OFTEC-style clearance and access rules as oil, runs standard gas-rated boilers with only a change of injector and pressure setting rather than a different boiler entirely. It suits households that want a gas hob and gas-style modulation rather than an oil burner's on/off firing pattern. The tank still needs delivery access for a tanker, which on some rural driveways is the deciding factor over oil. We check the access route for the largest realistic delivery vehicle before recommending LPG over oil, because a tank that can't be filled easily causes more disruption than the fuel choice was meant to solve.

Radiator sizing after lowering the flow temperature

Running a boiler at a lower flow temperature — typically 55°C or below rather than the old default of 70-80°C — improves condensing efficiency measurably, but it also reduces the heat output of every radiator in the house, because a radiator's output falls roughly with the square of the temperature difference to the room. Radiators sized correctly for a 75°C flow can end up unable to heat the room properly at 55°C unless they're upsized or supplemented. We check each radiator against the lower design flow temperature before recommending it, and where a room falls short we look at whether a larger single panel, a double panel, or an additional radiator on that circuit closes the gap, rather than pushing the flow temperature back up and giving away the efficiency gain.

How a condensing boiler recovers extra heat

A condensing boiler passes flue gases through a secondary heat exchanger before they leave the flue, extracting additional heat by condensing water vapour in the exhaust back into liquid, which is expelled as the mildly acidic condensate water down the drain. This is why every condensing boiler needs a condensate drainage route as part of its installation, unlike older non-condensing boilers, which simply vented hot dry gas straight out. The efficiency benefit only fully materialises when the boiler is actually condensing regularly, which needs a return water temperature low enough — generally below 55°C — for water vapour to condense in the first place. A condensing boiler run permanently at a high flow temperature can spend much of its time not actually condensing, which is one of the main reasons flow temperature settings matter as much as the boiler model chosen.

Chasing pipework into lime plaster and stone walls

Solid stone or cob walls finished in lime plaster, common in the older parts of Croscombe, behave very differently to modern plasterboard when a pipe run needs chasing in. Lime plaster is softer and more porous than gypsum, so cutting a neat, consistent chase without blowing the surface needs a slower hand and finer disc than a stud-wall job, and any repair has to be made good in a lime-based skim rather than modern filler, which can trap moisture behind it and cause the patch to fail. On solid stone we sometimes surface-mount pipework in painted conduit instead of chasing, particularly where the wall is a significant structural thickness and chasing would weaken it. Knowing which approach a wall needs before starting avoids expensive plaster damage.

Plume management kits for restricted flue positions

Where the ideal, shortest flue route would discharge too close to a boundary, a window, or onto a neighbouring property — a common constraint on tight plots in Croscombe — a plume management kit extends the flue's discharge point away from the boiler's own wall penetration, directing the visible water vapour plume and flue gases to a compliant location instead. It adds ductwork and sometimes a small additional fan to overcome the extra resistance, and it has to be specified against the specific boiler's approved kit range rather than improvised, since flue certification only covers tested combinations. It's a legitimate way to fit a boiler on a plot where the compliant flue route and the sensible boiler location aren't the same wall, without compromising on clearances to solve it.

Wood-burning stoves with a back boiler alongside a main boiler

Some older rural properties around Croscombe run a wood-burning stove with a back boiler feeding heat into the same central heating circuit as an oil or gas boiler, usually through a thermal store or a cylinder with two coils. Getting this combination to work safely means the stove's back boiler circuit has its own means of dissipating heat if the pump fails or a valve closes while the stove is still burning — a stove can't simply be switched off the way a boiler can if its heat has nowhere to go, so a gravity-fed safety circuit or heat leak radiator is normally required. It's a more involved design than a single-boiler system and needs planning at the point either appliance is replaced, not treated as an afterthought once the new boiler is already fitted.

Other boiler services in Croscombe

Worcester Bosch Accredited · 10 Year Guarantee*

New Worcester boiler with a 10 year guarantee*

Free no-obligation quotes for installation, servicing & repairs across BA & BS postcodes.

07516 118198 Request a Quote